91141085993 Kenmore Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Cranberry Twp, PA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Heating element was fried.
Remove 2 nuts attaching element to oven. Pull element out 1" to 2" exposing electrical leads. Pull leads off old element. Replace with new. Toughest part is seeing the elements in a dark oven. Have a light handy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Loveland, OH
- Parts Used:
- WB04T10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket worn and needed to be replaced
I simply removed the old one and installed then new one. No special tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SANTA MARIA, CA
- Parts Used:
- WB44T10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broiler Element Repair
I was attempting to replace the broiler element on the oven, but I discovered that the wiring may be the actual problem. I suggest before you order parts for a broiler repair, that you test the wires to ensure that you have continuity. I will have to trace the wires back to the source (the other element works fine) and see if I can find the problem with the current. I will keep the broiler element I ordered until I can confirm that the old element works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darthy from Dacula, GA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Bake element was broken and needed to be replaced
The repair was very simple. In fact the biggest challenge was finding the correct socket set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orion from Vancouver, WA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven temperature was low when reading was correct
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Perryville, AR
- Parts Used:
- WB44T10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating Element
Removed two screws, removed two wires, installed new element. So easy a caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wanda from elizabethton, TN
- Parts Used:
- WB57T10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
outer glass shattered on oven door.
I ordered a replacement glass from PartSelect and after i received the glass, I removed the oven door and placed it on a sturdy table. Then i removed the screws around the outer frame and lifted the door apart. I then cleaned out the remaining glass shreds from the frame and placed the new glass into position in the frame. I then replaced the screws back into the outer frame and placed the door back onto the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from pittstown, NJ
- Parts Used:
- WB44T10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Broil element on top oven was not working
Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from marstons mills, MA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower heat element burned out
Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Thornton, CO
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven lights were burning out regularly
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEONARD from NEWPORT NEWS, VA
- Parts Used:
- WB24T10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Cooling Fan Would Not Shut Off.
Loosen top panel (3 srews). Remove limit switch (approx 1-inch diameter disk), after unhooking two wires and removing two screws). (Limit switch on left upper side. ) Replace limit switch and top panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- annie from san diego, CA
- Parts Used:
- WB57T10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke the bottom glass door with a chair
I unscrewed the four bottom phillip screws to loosen the rail where the glass sits. Then I loosened the two side screws that hold the door handle and I was able to move the upper rail just enough to be able to slide the glass panel where it goes. I then aligned the glass panel making sure it was secured on the bottom and upper rails. I put back the screws and tighten them to keep the panel from moving. It was a very simple part to install. Thanks for your quick delivery.
Was this instruction helpful to you?
Thank you for voting!