6654438913 Kenmore Wall Oven - Instructions

Pop old one out and new one in

The replacement of the glass was easy, I removed the door and placed on work bench. As long as you lay the parts out in an orderly manner the reassembly goes pretty good. The longest time was cleaning the glass's that were dirty from the inner broken glass.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

First I checked to make sure the power was off with an electrical meter (wiggins). Next I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then pulled off the 2 wires replaced the element and put the 2 wires on the new element. I screwed it back into place and tested the element. When I turned the oven on my new element began to glow red and the repair was now complete. Super easy.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then reverse the process and bingo ...done

EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .

my wife took the old element out i used a screw driver to remove it...i then ordered the new part using this web site...i then let my wife install the new element she then attatched the wires she used her fingers to tighten the bolt....and she is very very impressed with herself.

ordered new broiler pan

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Easy unplug appliance take racks out unscrew two screws gently pull out element unplug two wires put new one in reverse .

Took a phillips head screwdriver and took out the two screws. Lifted off small plate securing screws, pulled lightly and wiggled the element out and popped the new one in. Total time 7 minutes - yes we timed it!!! Fast delivery too!!!

Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested

I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

I'll tell you.......PartSelect said the items would take from 3-5 days.....I got them in 48 hrs. I turned the breaker to the oven off. I unscrewd two screws from the back of the oven and pulled the element out and took it off of two connectors. Repeated the same with the broiler element. Job done saved $200.00...Job was quoted at $259.00

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.