79046599500 Kenmore Wall Oven - Instructions

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Lay gasket across opening after you have cleaned out the crumbs and old gasket. with your left hand spread the opening and gently push the new gasket in, make sure the edges go down and under the cooktop and the panel where the knobs sit. It should be smooth and slant towards the cooktop.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Turned of breaker to stove. Removed knobs. Removed four plastic nuts under knobs. Removed five screws that hold swith plate in place. Removed two screws that held actual switch in place. Swaped one wire at a time to new switches. (Switch was a newer model so seeing switch markings was critical to correct wire replacement!) Installed in reverse order. All in all. The job was easy and the new swith looks to be of a higher quality. This ia a gee-wiz--when the old switch failed it failed to the full on position. I had a pot of chicken slowly simering on Lo went to the garage to work a project came back in to a house filled w smoke/alarms going off and the burner on full high-glowing! The old switch was dangerous!

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

watched a U-Tube video on this subject.....worked like aa charm!!

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.

Husband made install in very short time. Nice to have them back in operation.