91141185991 Kenmore Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bradley from Perryville, AR
- Parts Used:
- WB44T10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating Element
Removed two screws, removed two wires, installed new element. So easy a caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from marstons mills, MA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower heat element burned out
Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Redding, CA
- Parts Used:
- WB23X5340
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
oven continued to get F2, F3 and F5 error messages when ovewn got hot
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Bethesda, MD
- Parts Used:
- WB44K5017
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Broiler element fails to heat
Feedback on site warned me that broiler element is only connected to oven wiring with press-on spade lugs rather than screws. Even with care I managed to 'lose' a wire and had to retrieve it with section of stiff coat-hanger wire bent into a hook. Coming off that experience, I soldered the spade terminals together before reassembly to avoid a repeat. New element, however, failed to rectify problem. Professional technician found main control unit defective -- a $300 part including installation, but at least GE still has it available. My advice to others in this situation is to remove old element before ordering a replacement, and test with meter to see if it's defective. It may or may not be worth going beyond an element replacement to you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- annie from san diego, CA
- Parts Used:
- WB57T10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke the bottom glass door with a chair
I unscrewed the four bottom phillip screws to loosen the rail where the glass sits. Then I loosened the two side screws that hold the door handle and I was able to move the upper rail just enough to be able to slide the glass panel where it goes. I then aligned the glass panel making sure it was secured on the bottom and upper rails. I put back the screws and tighten them to keep the panel from moving. It was a very simple part to install. Thanks for your quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Tacoma, WA
- Parts Used:
- WB27T10283
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
FO codes from panel
self diagnostics r neet for this GE/Kinmore oven..Conrol panel staying on....
Was this instruction helpful to you?
Thank you for voting!