Models > 9114742590 > Instructions

9114742590 Kenmore Wall Oven - Instructions

Jump to:

All Instructions for the 9114742590

Customer:: William from Centreville, VA
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Short circuited/burned out upper bake element

This is a simple repair of the PS249249 UPPER BAKE ELEMENT requiring only a 1/4 in nut driver or socket wrench.

1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.

Make sure not to remove any insulation.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Reba from Pleasanton,, TX
Parts Used:: WB44K5013, WB2X9719
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Baking element cracked and would not heat

I turned off the electricity to the oven.and removed the door.
I removed the 2 screws with a nut driver holding the element in place, pulled the element out about 3 inches and disconnected the two wires with pliers , clamped the 2 wires together to keep them from falling in the back of liner.
When the new element was received the procedure was reversed. Electricity was restored and the oven works perfectly.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jim from Arlington, MA
Parts Used:: WB44K5013, WB2X9719
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

The bake elemement burned out & the clips for the top element were broken

The bake element basically just plugs in remove the two screws in the back with a nut driver pull the element out unplug the spade connectors and reconnect the new element . As far as the clips just snap them on to the top element and snap back in the holes at the top of the oven.
Also very fast delivery less then 48 hours from ordering to delivery

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Doris from Aberdeen, NJ
Parts Used:: WB2X9719
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Hanging broiler

Quick and easy, thanks!

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: james from keller, TX
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

broken element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jack from Corinth, MS
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Bake burned out, checked open with an ohm meter

removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Elwood from Allen, MD
Parts Used:: WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

I researched the part number from partselect.com, ordered it and in less than a week (even in all the snow!) I had my part. Fifteen minutes later, my wife was broiling dinner! I repaired my broiler element without waiting on a repairman and for less than $50.00!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Cynthia from Pierson, MI
Parts Used:: WB44K5013
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Bake element burned out

My husband (a retired tool & die maker) easily removed the old bake element after first turning off the circuit. He cleaned up the burned salt that we had used to try to put the "fire" out but finally just shut down the circuit. Then just as easily istalled the new element. Thanks to your quick service, we were only without the use of the oven for a day and a half!

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: tim from fort scott, KS
Parts Used:: WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Wrench set

Upper over broil unit burned out

This part is a plug-in unit - two screws off; unplug the old unit; plug in the new unit; two screws on. Very simple.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Aaron J. from Bartlett, TN
Parts Used:: WB44K5013, WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Oven elements were not heating properly.

I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.

A very easy job to perform thanks to right parts from PartSelect.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: James from MARIETTA, GA
Parts Used:: WB44K5013
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

New element had blade connectors (male).

Drilled small holes in blades to accept existing machine screws from oven wires.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gilbert from Clarkston, MI
Parts Used:: WB44K5009
Difficulty Level:: Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set

Broiler element blew out.

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: John from CASPER, WY
Parts Used:: WB21X5301
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers, Socket set

Bad sensor

By myself

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Harden from Lynchburg, VA
Parts Used:: WB44K5009
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Element burned out.

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Richard from Maitland, FL
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

bake element burned out

removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the 9114742590