79099503992 Kenmore Wall Oven - Instructions

Easy as 1-2-3

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

slid it in

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Took screws loose, unplugged old one plugged in new one put screws back

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

This repair was easy, but I would not have even tried if I hadn't read the tips from other DIYers - thanks! The website questions and schematic along with some common sense testing isolated the problem with the oven only heating up to 250 degrees. Since the broiler (upper element) worked ok, that made it likely that the temperature sensor was not the problem. That made almost certain that the bake (cooking) element was the problem. So, I ordered the part, which was delivered quickly. Early on the morning of the scheduled delivery date, I turned off the oven power at the fuse box and pulled the oven away from the wall. There were only 4 screws to remove in order to take off the rear panel. The bake element was attached to two slide-on connectors, one of which looked charred and partially disconnected. I cleaned the charred connector, reattached it to the bake element, turned the power back on, and then turned the oven on. The charred connection glowed, so I immediately turned off the oven and the power. I disconnected the bad connector, cut it off from the wire, and stripped the wire to prepare for a new connector, which cost 30 cents at the hardware store. The bake element connection was cleaned, and then the new connector was attached. The power was turned back on, and then the oven was turned on, and it heated perfectly. After confirming several heatings over several hours, the rear panel was reattached, and the oven was pushed back to the wall. This expensive 40" dual fuel oven had been purchased new and used for 3 years by the prior owners of our home. The oven's computer brain died when the oven was 7 years old - the repair cost us $500 for professional labor, parts, and materials. I don't know if I could have done that repair, but I had no intention of shelling that much again, which is why I tried this bake element repair myself. The oven is now 11 years old, and the most likely part to fail is the original bake element. So, we may keep the new part as insurance with the hope of making a fast, easy, inexpensive repair when the original bake element eventually fails.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

I previously replaced terminal blocks and elements so the infinite switch was the last stop before new purchase. I reviewed the online repair video. Unplugged the range and removed the three screws from the rear of the control panel. I Removed the knobs then removed two screws to release the front plate behind the knobs. I removed the two screws securing switch #1 and compaired to the new parts before removing wires. Wire locations were labled the same but in different sequence. I located the knob adapter for my knobs and set them asside. At first I thought the rod coming out of the new switch was too long and then figured out that the indentions allong the rod were to be broken off to the correct length. ( re-reading the included instructions was nearly useless - - not in plain language ) I used a pair of vice-grips clamped just below the length of rod I wanted to break off and it snapped off easily and cleanly for the most part. ( A word to the wise, this is some really soft metal at the breaks along the rod. I attempted a second break on one switch after mounting in the control panel and the thing broke off at the short end - - scary ) luckily I was still able to use it with my knobs and adapters. I relocated the switch wires to the new switch one at a time matching label to label ( L1, L2, H1, H2, P) then mounted the new switch into the control panel. I re-assembled the range and it is heating better than ever. Well worth the effort and minimal expense compared to a service call or replacement range.

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!