91140169690 Kenmore Wall Oven - Instructions

This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!

When i finally got the right part.It only took few minutes to screw in and it worked perfectly.Customer support was very helpful in finding the correct part.thanks

Used nut driver, removed 2 screws and removed old element. Reversed procedure for installion of new part. Can't believe ordered part one day & recieved it next day. Fantastic service. Will definitely call company again.

Installation was really easy. Remove the old bake element, plug the new one in, took at most 10 minutes.

had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.

Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.

ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.

Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.

I removed the two screws holding the element in, pulled it out, and unplugged it. Installation was reverse of removal. It's just that simple.

Remove control panel: Made a layout of the wire colors and IDs. The new panel was sighly different. Had additional conponent which I ignored because it did not match the wires or IDs I had recorded. The only wire that I did not connect was the ground (Green wire) The place for it on the new board was crossed out. After I placed the wires where it should go on the new board and turned back on the power. I tested all the functions and they all worked the firsy time. I was very happy with the results. What I think they should provide with the new panel was a conponet layout of the new board.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.