9114703993 Kenmore Wall Oven - Instructions

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

I pulled the old broiler from holding clamps. I unscrewed the 2 screws holding the old broiler, pulled it out very slowly while using clips to hold the wires from going back into the wall behind the oven. That’s very important, I then pulled the old broiler off and replaced the new one. First I secured the elements on the oven clips that hold the element up, I reattach the new element, screwed the 2 screws back in. DONE My grandson helped, total time, maybe 15 minutes. Watch their video. Really easy, save money.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Be sure to flip the breaker to the oven to the OFF position before doing anything. Take out the two screws at the back of the oven that hold the element. Carefully pull the element forewarn to expose the connections to the wires. Disconnect the element from the wiring connectors. Be careful not to damage the connectors or the wiring. Plug the new element into the wiring connectors. Make sure you have the connections firmly in place. Push the wiring and connectors back into place. Replace the two screws. Make sure the element is resting in the spacers that keep it the correct distance from the top of the oven. Flip the breaker to the ON position, Turn the oven on Broil. The element should start turning a bright red. some fumes will come off the element. That is just oil from processing and handling. Your done!

1. Turn breaker off at breaker box. 2.Disconnect old broil element. Pull electric wires out 3-4 inches from BACK of oven. Clamp wires or tie off so they do not retreat behind back oven wall. INSTALL wires to new element and secure back plate. Install NEW clamps to new element. Switch on breaker and check operation.

Quick and easy, thanks!

it was real easy, I just watched my husband do it!

Turned AC off. Removed bracket screws and pulled out ac connections. Removed old element and reilstalled new element and set AC on.

We removed the two very tiny screws that held the plate through which the element was connected to the wiring. It was extremely difficult to do so, because the screws were so tiny. Our socket set did not have such a small attachment, and we had to use an adjustable wrench. Once we accomplished that, we unhooked the old broil element from the wires. At that point, the wires snapped back into the wall. There was almost no slack to pull the wires back out into the oven so that we could hook the new broil element up. It took more than an hour of maneuvering before we were able to get hold of enough of the wires so that we could grab onto each one and hook up the new broil element. One we did that, it was easy to place the broil element back into its brackets.

As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman

First turn circuit breaker off. Remove two retaining screws, disconnect two connectors at the end of the element, toss old element and reverse the procedure
to install.

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

I turned off the electricity to the oven.and removed the door.
I removed the 2 screws with a nut driver holding the element in place, pulled the element out about 3 inches and disconnected the two wires with pliers , clamped the 2 wires together to keep them from falling in the back of liner.
When the new element was received the procedure was reversed. Electricity was restored and the oven works perfectly.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws

removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.