79046824100 Kenmore Wall Oven - Instructions

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

I looked online and read what other people had done. The best advice was keeping all the screws in the order they were taken out. I also separated the screws that had come from the top, sides and inner side of the door. This helped immensely as I reassembled the door. I spread out a heavy garbage bag that I cut open. This kept debris and glass off of my kitchen floor. This is NOT a difficult repair; Parts Select said it would take three days to get me the glass; it arrived in TWO! Start to finish, the entire job took just about an hour. I saved myself over $100, and again, this is NOT difficult!

Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.

Based on previous responses we anticipated this repair to be easy, however, it was a little more challenging than expected. The method of repair was easy enough, just would have been better if there had been more wire to pull out to connect to the new bake element. It took two of us to fish for the wires back inside the stove with a needle-nose pliers after removing the element. One had to hold the wire with the pliers while it took the other to attach it to the new element with second pair of pliers as there was no room for using fingers. Retrieving and attaching the second wire to the element was even more challenging because now the half-attached element was in the way. Disappointed and not sure why the element burned out in the first place on a 4year old appliance.

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center portion was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

Self easy

PS Great service Super FAST.
Thanks Jesse

I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor

Turn off the electricity
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

Twisted replacement bulb into place easily. Let there be light!

1. SHUT OFF POWER TO YOUR RANGE! (I flipped the circuit breaker at the box to do this. To be totally safe, you can shut off the power to the whole house.) 2. Remove the oven racks. 3. Undo the two screws (save for step 8) holding the bake element in place. (This took some doing for me, as the screws did not want to come out easily. Maybe use some penetrating oil and be careful not to strip the screws.) 4. Gently pull the bake element toward you, exposing the contacts and wires. 5. Remove the wires from the old element's contacts. (Remember which contact 6. Attach the wires to the new element's contacts. 7. CAREFULLY push the wires back into the wall of the oven. (Pay attention to the insulation. Make sure that some insulation is near the wall.) 8. Fasten element to wall of oven with screws you saved from step 2.

removed 1 screw from each glide, pulled parts out, replaced parts and screws, slid drawer glides into bearing glides. job done, very easy and fixed problem.

1. Turn off power to the electric oven
2. Removed the two screws in the top side of the oven that hold it into the cabinet.
3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job.
4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge.
5. Unplugged sensor
6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front.
7. Side the new thermal sensor in place replace the screws.
8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor.
9. Replace the back and replace the screws.
10. Slide oven back into the wall.
11. Replace the two screws that hold the oven in place in the frame.
12. Turn power back on
Check the temperature

My husband followed the video instructions and it was easy to fix.

I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first