Models > 9114742595 > Instructions

9114742595 Kenmore Wall Oven - Instructions

Jump to:

All Instructions for the 9114742595

Customer:: William from Centreville, VA
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Short circuited/burned out upper bake element

This is a simple repair of the PS249249 UPPER BAKE ELEMENT requiring only a 1/4 in nut driver or socket wrench.

1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.

Make sure not to remove any insulation.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Elwood from Allen, MD
Parts Used:: WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

I researched the part number from partselect.com, ordered it and in less than a week (even in all the snow!) I had my part. Fifteen minutes later, my wife was broiling dinner! I repaired my broiler element without waiting on a repairman and for less than $50.00!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: james from keller, TX
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

broken element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jack from Corinth, MS
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Bake burned out, checked open with an ohm meter

removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gilbert from Clarkston, MI
Parts Used:: WB44K5009
Difficulty Level:: Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set

Broiler element blew out.

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Charles from Gastonia, NC
Parts Used:: WB27K5167
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers

The clock plate on the clock and oven controls has cracked.

I basically had to disassemble the top part of the stove to get the clock out. Once I got the clock out, replacing the plate was trivial. It attaches with a sticky/tacky back. Reassembling the stove took another 30 mins, but went relatively smoothly. The final job looks great and the stove seems to function as usual.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Aaron J. from Bartlett, TN
Parts Used:: WB44K5013, WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Oven elements were not heating properly.

I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.

A very easy job to perform thanks to right parts from PartSelect.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Harden from Lynchburg, VA
Parts Used:: WB44K5009
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Element burned out.

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Richard from Maitland, FL
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

bake element burned out

removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Marsha from Charlotte, NC
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

broken element

turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Eugene from San Rafael, CA
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Oven Element melted

Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Toni Ann from Manalapan, NJ
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

The baking element broke.

Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: KY from Lenapah, OK
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Oven would not heat

Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Lynne from Coto de Caza, CA
Parts Used:: WB44K5013
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Baking Element wouldn't heat but the broiler worked fine.

First I turned off the power at the fuse box, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced with the new element. Very Easy!

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Beverly from Baton Rouge, LA
Parts Used:: WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Burned out broil element

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the 9114742595