91148365791 Kenmore Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DANNY from GROVE CITY, OH
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
element was bad, not heating
had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tammy from newberg, OR
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
top oven bake element blew up
When i finally got the right part.It only took few minutes to screw in and it worked perfectly.Customer support was very helpful in finding the correct part.thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Waco, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom baking element had burned out
I simply removed the two screws but the back of the element holding it in place and pulled the element out far enough to clearly see the wiring. (TURN OFF THE ELECTRICTY TO THE OVEN). Gently pull the snap connectors off the element leads and snap them on the replacement element, push wiring back into oven opening, tighten down screws, clean up and close the door. Turn electricty back on and start the oven. It will smell for a few moinutes while the element heats up for the first time. You are good to go. To Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Freeport, NY
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower Bake Element Had Cancer-Like Freeakout!
Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Charleston, MS
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out bake element
I cut of electric braker in fuse box, unscrewed two screws and replaced element in less than five minutes, really easy task. Oven worked well. Thank you Park Select, good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from Dallas, TX
- Parts Used:
- WB48T10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing racks
took the old ones out and put the new ones in their slots. No issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from White River Junction, VT
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
New bake element
I am 68 years old and found that changing element was a breeze---using pliers removed nuts--unhooked bad element--rehooked new element---done------------recieved new element in 2 days--------- Thanks -----------------
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from N Las Vegas, NV
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower Element Partially Heating
I removed the two screws holding the element in, pulled it out, and unplugged it. Installation was reverse of removal. It's just that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- delbert from lewisville, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
heating element for the oven broke in two
ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!