2784288891 Kenmore Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Les from Coal Creek, CO
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Midlothian, VA
- Parts Used:
- WB44M5
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench (Adjustable)
Broiler Element Burned Out
1)Undid two hex nuts holding broiler element in place. 2)Slipped fasteners off pegs connecting element to oven. 3)Simply reversed the process, when installing new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Marietta, GA
- Parts Used:
- WB2X9151
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in oven had blown and needed to be replaced
I did not do it, I instead had my neighbor put the gasket around the light lens cover and replace it. He considers himself a handy man, so it was easy for him.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chuck from battle creek, MI
- Parts Used:
- WB44M5
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burnt out element
turn off power, remove 2 screws, lift off of hanger , slide out far enough to unplug wires. remove brackets from old element, I did have to use a screw driver to open up bracket to slide over new element(new element a little larger diameter coil) reverse removal. DONE !! Thank You Part Select !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from fort mill, SC
- Parts Used:
- WB44M5
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broiler element burned out
shut off power to range, removed old element, looked up part on line, shopped for best price, Part select was $30 less than sears replacement part, ordered part, part arrived in 4 days, installed new part and I was broling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kris from Greensburg, PA
- Parts Used:
- WB44X238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element burned out
Putting a new one is very easy. Just trip the fuse, unscrew two 1/4" screws, pull the element out, connect the new one and screw to the back of the oven. Turn on the power and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!