REP307CW3 Kelvinator Wall Oven - Instructions

Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

Easy as 1-2-3

The wire on one side was stuck in the hole in the back and had to take the back off. It was easy to find and push through. I just connected the two wires to the new element and all was well again.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Reviewed a YouTube video. Then removed the old element and installed the new one. It was extremely simple! I became my husband's hero instantly!

I have a wonderful range that I love and it is almost 30 years old! The baking element died...burned and broke in half. This is the second time I have had to replace it (not bad for the old girl) and the first time I used PartSelect. I ordered the part late in the day and it was delivered by FedEx in just under 24 hours....now that's service! This is a very easy repair that anyone can do. Just turn power off to range, unscrew the hexagonal screws, ease out the bad element, reattach electrodes to new one, ease it back into range, put screws back in and you are done. Ten minute job you can do yourself for the cost of the part. Great great service from PartSelect.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

The PartsSelect site provided the hint that the baking element might be the root cause of low heat. SO I order the part, got it within a few days and installed it. Simple matter of removing a small read cover and tow faston connectors to the heatng element along with two Phillips screws that secured the heating element. Oven now works like new!! Thanks PartsSelect, you saved me a bundle!