W2451B Jenn-Air Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sam from Garland, TX
- Parts Used:
- 71001129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door switch for oven light
1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel.
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yvonne from Lake Odessa, MI
- Parts Used:
- 71001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door Lock Switch fell apart
My son removed the switch panel and unpluged
the switch. Then he replaced it with the new
switch fasten back the panel and turned the
power back on and everythiing worked fine.
the switch. Then he replaced it with the new
switch fasten back the panel and turned the
power back on and everythiing worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Mulkeytown, IL
- Parts Used:
- 703917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken temperature knob on my oven
This was obviously not a hard repair, I just replaced the knob. I would like to say that I did receive the part in just a little over 24 hours. That was nice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Byron from LE SUEUR, MN
- Parts Used:
- WP74003387, 8009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb and socket became one when trying to remove a burned out bulb. Ruined the socket.
Move stove out from wall. Unplug from power. Removed four screws from the left side of the back (the side the light socket is on. Reach in and unplug the two wires on the back of the bulb socket assembly. Inside the oven, remove the bulb cover and the two screws holding the socket assembly. Remove assembly. Install bulb in new assembly, reattach the assembly to the oven back, reinstall the bulb cover. On the back of the stove, replug the two wires and replace the screws on the stove's back cover. Replug the unit to power and move back into position.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mohd fouad alahdab ruh from JAMAICA, NY
- Parts Used:
- WP74003387
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
The oven light went off, changing the bulb did’n’t solve the proble, beacause the socket was burned.
First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Belchertown, MA
- Parts Used:
- 71001129
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven door slammed shut and the door lock switch broke causing the light to stay on continuously.
I contacted a local appliance repair store who didn't know what I was talking about. I looked online and the store called me back to tell me the part would probably be $75.00. I took the broken part out of the door frame and found the exact part online at your site, and ordered it for $14.00. Received the part within 2 days and put it in in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Rocklin, CA
- Parts Used:
- Y701721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the fan started making noises like it was shaking
I pulled off the facia from the microwave/oven. Unscrewed the plate holding the microwave and slid out the microwave. The microwave and oven are a unit. I unscrewed the oven from the hole it sits in and slid out the oven and set it on a sturdy chair. Then I unscrewed (6 screws) the bracket that holds the microwave to the oven. After that I unscrewed (14 screws) the top sheetmetal plate on the oven and slid that around behind the oven. Then I unscrewed the grounding strap inside. Did the 2 screws on each side of the oven holding the fan unit and slid that out. Undid the 2 wires plugged into the motor and the 2 screws holding the fan motor. Then I slid off the fan from the old motor and slid it onto the new motor and reversed the whole process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from IDAHO FALLS, ID
- Parts Used:
- WP5700M600-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door Glass Broken inside
Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edie from SANTA FE, NM
- Parts Used:
- WP701650
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Replacement of old oven door seal
Removed door (that was the most difficult part)
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Smithfield, VA
- Parts Used:
- WPY04100514
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The broiler would not heat. I saw a bad place in the element. Ordered a new one.
Received the new one. Installed it in 15 minutes. Thanks for the fast service.I will buy from you guys the next time I need a part ! Thank You, Henry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!