W136-C Jenn-Air Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn from Saginaw, MI
- Parts Used:
- 866294
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My oven light would NOT shut off
Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V
It took about 5 min. to turn off the electric & to turn it back on.
Glen V
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blanche from Woonsocket, RI
- Parts Used:
- 74003387
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light bulb socket broken
Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James Edward from Gardnerville, NV
- Parts Used:
- 703901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Selector Knob broke after 20+ years!
Old (broken) knob was gone, so wife oriented new knob over selector shaft, and pushed onto shaft!! PROBLEM FIXED!!!!! No fuss, no mess - just as good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from springfield, PA
- Parts Used:
- WPY04100514
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Failed Broiler element
Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vern from Sugar Land, TX
- Parts Used:
- WP701650
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door seals worn
Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from McKinney, TX
- Parts Used:
- WP7711P492-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic knob
Placed new knob directly on post. No problem
Was this instruction helpful to you?
Thank you for voting!