W30400PV Jenn-Air Wall Oven - Instructions

The front panel was removed by unscrewing six screws just above the oven door and then four nuts were removed fron the burner assy. using a nut driver. The circuit board with the clock assy was then available. It was then just a matter of removing three cable connectors and a ribbon cable connector and two screws to remove the old clock assy. The reverse was done to install the new clock assy. The whole operation took about 15 minutes.

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Popped it in and now we have a well lighted control panel AND a night light for the kitchen. Just wish Jen air would design a longer lasting part!!!

I shut down power at the circuit breaker, removed the stove knobs, unscrewed the underneath screws of the front panel, pulled off the panel, and the electronic board/panel was there.

I unhooked the wires (3 sets), and used the socket to remove the electronic board from the front panel. I put it all back together. Very easy-- less than 15 minutes!

Removed 8 screws and replaced the part (also did a good cleaning while we were in there)! Easy breezy!!!

First, DISCONNECT POWER or you can turn your panel into an arc welder. After that removed four screws that hold front panel in place and 2 screws that hold the display in place. disconnect ribbon cable and two other cables. Reverse operation for assembly.

For the self cleaning problem, replace door lock switch by pulling forward, use needle nose to remove & replace connector. Push into place. Very easy. Total 10 minutes for both jobs

ordered new broiler pan

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

My husband removed the faceplate, removed the old clock and but new clock in, then he replaced faceplate. It was very easy.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Initially I made a false start by pulling out the stove, which was not necessary. Then dropped control panel by removing the several screws on the bottom of control panel. Removed the three connecting cables by freeing locking mechanisms. (The locks on the ribbon assembly are on both ends of the connector plug). Removal of circuit board then obvious. Installation of new circuit board quick and easy. All displays then worked OK. I added a fiberglass heat shield around the circuit board and time will tell if this worked or was a mistake;
Your troublshooting tips were very helpful.

I am curious how the chap who found capacitor C3 to be defective zeroed in on it without a test harness.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.