S166B-C Jenn-Air Wall Oven - Instructions

I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.

Turn the power off to the oven. Removed two screws on the back of the oven which held the element in place. Gently pulled out element and unhooked it from the clips. I then got the new element and hooked it back into the clips. I pushed it back in and replaced the two screws. Restored the power and turned on the oven. It works like new!

Wife installed them, they just snap into place on the Rock Grate.

I simply removed all the oven racks so I could reach in, removed two screws, un-clipped the old element and clipped in the new one. Put the screws back in and popped in a chicken ready to bake. Delicious.

In a nutshell, I followed the very well-defined & detailed instructions posted by others on this website for the same part replacement. The installation went well!

Removed 2 mount screws, slid element toward me to expose the wire attachment to the spades on the loop. Reversed the process with the new element and installed the screws.

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.

I shut off the power to the unit took out a couple screws , the bad element . Replaced the new element turned on power and that was that a quick process and oven is working like a charm. Thankyou

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.

removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.