W30400PR Jenn-Air Wall Oven - Instructions

Loosened the contol panel until I was able to get to the Digital Display board.
Removed the three cables and the screws that held the display unit to the control panel.
Reversed the procedure to instll new digital clock display unit.

1. Removed knobs and front panel. Disconnect wiring.
2. Order part and installed. Done

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Removed screws on face plate, disconnected wires, placed on counter, removed hex head screws. Removed one end of electric type circutry, replaced with new part and reassembled.

I first turned the breaker off. Then removed the screws under the display with the oven door open. Then removed the side screws. Then removed the trim kit for the microwave which exposed 3 more screws. The middle one with the Micro Door open. The complete display panel then was removable. I took a digital picture of the 2 wire and 1 ribbon connectiors (I know-anal). Then removed the 2 wire groups-struggled somewhat with the ribbon connector until I realized by trial & Error that the 2 little tabs on the sides only pull upward, releasing the ribbon. Removed 4 nutdriver screws to remove old display-installed new one in reverse fashion. Then I CLEANED everything I could reach it was so dirty! (I live in the desert,duh!) I just paid great attention to how it came apart and it was relatively easy. The best part is that I didn't have to remove the Oven/Microwave unit to do the repair.The new part works perfectly, thanks!

I replaced the heating element but that didn’t help. So then I replaced the oven sensor and that didn’t work either. Both were pretty easy to do but I’ve now spend $170 and my oven still isn’t working. I called number listed and got a recording that all agents were busy and there was a high call volume so I can’t get any help.

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

1) Unplug Appliance
2) Remove stove front (4 hex-head screws)
(Note: support front while removing screws)
3) disconnect (3) wiring harnesses
(Note: exercise care when revoving "data bus", release with small "dogs" on each side of plug.)
4) Remove Clock assembly (2 hex-head screws)
5) Replace Clock assembly (2 hex-head screws)
6) Reconnect (3) wiring harnesses (reseat bus plug dogs)
7) Reattach stove front (4 hex-head screws)
8) Plug appliance in to power outlet

Note: Before the repair, all functions and displays worked just fine, they just weren't illuminated so you couldn't read any thing. It really steams me that I had to pay $141 to replace a 50 cent light.

Remove four screws behind control knobs. Remove four hex nuts under control panel (open oven door to locate). Pull control panel down and out. Remove two hex nuts holding clock assembly. Remove three wire connectors on the old clock assembly and carefully insert on new clock assembly. Reverse instructions to re-assemble. It's a breeze to do! Took longer to get my tool box than the time it took to replace the clock assembly.

Turn off breaker to stove. Open oven door and remove screws up under display. Slide display down and tip top edge forward so you can see the back side. Remove 2 screws holding digital display and disconnect 3 wiring plugs. One of them is a ribon connector and you must squeeze it to make the front edge rise up to disconnet the ribbon and again when putting new part in. Reverse the proceedure. It took my husband 10 min to replace the part. Being able to read how others had done it was invaluable.

I removed the three screws that was on top of the display enclosure. I then removed the four screws on the bottom of the display enclosure.

I unplugged the two connectors going to the old enclosure and removed the enclosure to the kitchen table. I then pressed the two locks on the ribbon cable lock and pulled up on the ribbon cable lock. I was unsure how to do this, but if you press the two tabs and slightly pull up on the lock, the ribbon cable will come free.

I then removed the four screws holding on the old display and put the new part in. Fastened with the four screws and connected the ribbon cable, squeezing tabs and raising the black lock, inserting ribbon cable and pressing down to lock in place.

I then took the enclosure to the oven, connected the other two sets of wires and mounted the enclosure with the three upper scres and four bottom screws. Took me about 15 minutes. My $148 PartsSelect part was $267 locally.