WW30430PC Jenn-Air Wall Oven - Instructions

Built in so removed 4 screws underneath display and lifted up (was a little tricky because of cabnet doors above)removed 2 plug in connectors and put unit on counter top. to remove ribbon connector push in on tabs on both sides, lightly pull up ribbon (the wider part of connector will come up about a 32nd of an inch and the ribbon will pull away from that, there are two small protusions on the connector that capture two holes in the ribbon) once you figure that out its a simple job.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

Removed three screws from top of display/control panel. Open upper oven door and remove 4 screws from botton of display/control panel. Pulled panel off and rested it face down on top rack of I pulled out of upper oven. removed 2 wiring harnesses and ribbon wiring form clock assembly. Remove four screws with nutdriver and remove clock assembly. Replace clock assembly and reasseble in reverse order from above.

Thanks for the hint from this forum.
My display became very dimm, eventually unreadable.
WIth suggestion from this forum, I replaced the Electronic Clock assembly. I took me about 15 minutes. The display works perfectly fine and makes the oven look like new with its nice bright digits.
BJ

Removed screws holding in control panel. Replaced clock assembly following instructions listed by others. Easy. Wife happy.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

Easy repair- read the other reviews and followed it. Pretty straight forward.
Quick delivery on the part.

Removed the screws pulled the control panel out and plugged in the new one......it was easy. It was 2 days before Thanksgiving, we were so happy to get it fixed.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

Unscrew 7 screws on foace plate,unplug computer board,replace with new board,rescrew 7 screws ,finished

Turned off current at breaker box. Removed the panel above the top oven (dual-oven) by removing the seven screws that held it on. Disconnected the wires going to the clock assembly. Laid the entire panel face down on the counter, removed the four screws holding the clock assy in place and removed clock. Installed new clock and reinstalled panel. It was that easy!

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I read installation advise on this web site, so when the part arrived I was more than ready to replace it. Removing a few screws below the faceplate, pulling the faceplate out slightly then up, being careful with the electronic connections, (there are tabs on the sides that need to be pressed to remove the connectors. The largest connecter is tricky, the side tabs need to be pressed then gently pulled up to release the electronic "tape".) It took about ten minutes to complete. Very satisfied.