W27400W Jenn-Air Wall Oven - Instructions

I first turned off the circuit breaker for the range. I then I removed the four hex screws from the underside of the panel and then dropped the panel to expose the clock assembly. I then removed the two screws holding it in place, disconnected the cables and removed the old unit. I then reversed the procedure to install the new unit. I next turned on the circuit breaker restoring power to the range. And like magic I once again had light. I know I must have made by Daddy proud. I should have done it sooner. Thank you for making it so easy by sharing the "how to's" with me. It was especially helpful to have the model number.

Once the display became too dim to read, I removed the front panel to determine how to access the piece and to check part numbers so that I could order the proper piece. Once the part arrived, being familiar with the disassembly, it was simple enough to replace the part quickly. The part came out with two screws and the connections were standard electronic multi plug, making the replacement simple. When we turned the power to the unit on, it worked first time.

Turned off the breaker. Removed the screws under the front panel and eight screws behind the burner controls (two each). I then slid out the panel and laid it flat on top of the stove. Removed the three connectors. Most difficult was the ribbon connector: Squeeze the clips at each end and slide the top half of the connector up. Then the ribbon slides out (practice on the new part). Only two screws held the assembly in. Reverse the process with the new assembly. Worked great!

As described by many others before. Turned off the power at the circuit breaker panel for the house. Unscrewed the front panel, disconnected the three connections to the old assembly and unscrewed the assembly.

Cleaned a few pieces then screwed in an connected the new assembly, put it all back together, turned on the power, said a prayer and IT WORKED!

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Ordered part on line, part came within few days well wrapped and protected, very simple repair removed two mounting screws and two lead wires to remove burnt element, replaced with new one, wire were re-connected and the mounting screws secured the new element in place, about 20 min job.

My husband removed the faceplate, removed the old clock and but new clock in, then he replaced faceplate. It was very easy.

Popped it in and now we have a well lighted control panel AND a night light for the kitchen. Just wish Jen air would design a longer lasting part!!!

Removed 8 screws and replaced the part (also did a good cleaning while we were in there)! Easy breezy!!!

First, DISCONNECT POWER or you can turn your panel into an arc welder. After that removed four screws that hold front panel in place and 2 screws that hold the display in place. disconnect ribbon cable and two other cables. Reverse operation for assembly.

For the self cleaning problem, replace door lock switch by pulling forward, use needle nose to remove & replace connector. Push into place. Very easy. Total 10 minutes for both jobs

I shut down power at the circuit breaker, removed the stove knobs, unscrewed the underneath screws of the front panel, pulled off the panel, and the electronic board/panel was there.

I unhooked the wires (3 sets), and used the socket to remove the electronic board from the front panel. I put it all back together. Very easy-- less than 15 minutes!

first of all you had super fast shipping only 2 days from order to repaired complete. removed 2 screws and 2 wires replaced old heat coil with new one replaced 2 wires and 2 screws less than 5 mins.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

ordered new broiler pan