S156B-C Jenn-Air Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from ARCADIA, FL
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from IDAHO FALLS, ID
- Parts Used:
- WP5700M600-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door Glass Broken inside
Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from DIAMOND BAR, CA
- Parts Used:
- WP74003387, 866294
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Oven switch not working
Had to remove the glass top and the control panel and the panel bracket then use angled needle nosed pliers to compress the retainers then pull the switch from the inside of the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Portland, OR
- Parts Used:
- 12200039
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Fan and oven light would operate.
Removed the old part by removing the clips and wire connectors. Then placed the new switch in place and reapplied the wire connectors. Tried to then place the new clips on the posts but the clips were very fragile and they broke. Then decided to thread the posts and use nuts. Used a minature die to thread the posts, applied washers and nuts and finished the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from GAITHERSBURG, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
burner control stopped functioning.
Replaced the control.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Fair Oaks Ranch, TX
- Parts Used:
- 12001311
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Blower motor had frozen up.
Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Surface Burner control
Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Rochester Hills, MI
- Parts Used:
- 12200039
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Replaced the light /oven rocker switch
The two mounting clips supplied with the switch would not fit onto the two studs in the die casted plate (too small) . In removing one of the old clips, the stud broke off. Thus I had to break off the other stud and drill out the area to allow two screws to be inserted to mount the switch securely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Temple, TX
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned burner control out of warranty
switch power supply off at breaker panel
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from Newton, NH
- Parts Used:
- WP71002111, W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
grease filter did no fit much to large
switch went well
removed 4 screws and lifed front panal up and out
removed 4 screws and lifed front panal up and out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charlotte, NC
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
Was this instruction helpful to you?
Thank you for voting!