S156 Jenn-Air Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alan from Pleasant Hill, MO
- Parts Used:
- 12200039
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Downdraft fan would not operate with light/fan switch.
Removed old switch, but when I tried to install the new one the round slide on retainers that hold the switch in place were cheaply made and broke. I had to go to the hardware store to find replacement parts. Electric terminals matched correctly and slipped off and on just fine. New switch works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Decatur, GA
- Parts Used:
- WPY702338, WP7711P492-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven door seal was frayed, due to using oven cleaner.
First I removed 7 screws, using a Philips head screwdriver, to allow access to the inside of the oven door. I then removed several more screws to separate the panel holding the seal so that I could remove it and replace it with the new seal. Once the seal was in place I re-inserted all the screws to the panel and door to complete the repair. The knobs just slipped on to replace the ones that broke and fell off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Lebanon, TN
- Parts Used:
- 12200039
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The plastic holding the Switch for fan/light broke
A little difficult getting the old retaining washers off of the old part and placing the new washers on the new switch. I ended up using a nutdriver on the retaining nut and hitting it with a hammer. This worked great!! Make sure to record which wire color goes where on the old switch before removing wires. TURN OFF POWER BEFORE!! This is 220V. It can hurt you bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Rosebush, MI
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
one of the four burners was not working
Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lorton, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
RF burner would not heat
1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Anna Maria, FL
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new grease filter
Removed old grease filter,replaced with new grease filter. No tools needed.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Lafayette, LA
- Parts Used:
- 74011338, WP7518P054-60, 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn out / burned grill and components
very easy - not really a "repair" more of a face lift, although the grill was unusable.
Parts were perfect - Used it the same night.
Parts were perfect - Used it the same night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Centreville, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Infinite Rotary Control Failed
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.
gc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Bourbon, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sparks shot out from under knob, then, no surprise, the burner didn't work
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from castle rock, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
electric element would not function
2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valentine from Bow, NH
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch was no good
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Hubert, NC
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new grease filter
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)
:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Cottage Grove, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace grease filter
Nice filter. Exact fit. Had a little ring to use to pull out to clean. Shipment was packed well.
Was this instruction helpful to you?
Thank you for voting!