JJW9530DDS Jenn-Air Wall Oven - Instructions

Watch the video. Spot on instructions. Easy peasy.

I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

I took the broiler pan out of the shipping container and put it in the oven.

Pulled the double wall oven out about five inches and install replacement brackets on both sides. Reinstalled oven doors and slide ovens back. Piece of cake— the lower oven door closes better than when oven was installed 13 years ago. Believe I had a bracket problem from day one!

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

First I removed the oven door - with door fully open pull the clips on the hinges all the way out, then close door as far as it will go and lift the door up and off the oven.

Then I removed the three screws on each side, that hold the oven to the wooden cabinet. I then slid the oven unit out from the cabinet about 6 inches, to gain access to the hinge receptacles.

I then removed the 2 screws that secure the receptables to the oven body, and replaced the receptacles.

Reverse steps to put it back together.

Works like a charm.

After watching a you tube video or two, I easily detached the oven door. One of the hinges was jammed, and upon releasing it with a screwdriver, it snapped open and gashed my thumb. This as entirely my fault, I did not realize how much force was held in the spring.... You must remove the bottom frame piece and inside door pan to get to the hinges. All Phillips head screws, and all the same size. Once these are removed the hinges are easily removed with 3 Phillips head screws. While l was this far into it I removed the two layers of glass to clean them on both sides. This requires a small nut driver to remove the channels holding the glass. There are three layers of glass to clean on both sides, quite dirty and brown. Reassembled the whole thing. The door assembly popped right back in, and now functions like new. You can actually see into the oven, without opening the door!

Rotated the hinge lock with a screwdriver, pulled door off hinge bracket, later door on table, removed screws to detach inner door frame from outer door. Three screws to remove each hinge. Very easy.

Removed the door and the screws that secured the oven to the cabinet. Pulled the oven out about four inches to provide access to the hinge brackets. Removed two screws on each bracket and removed the brackets. Reversed the process and all was well. Works like new.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

First, I thought we were in big trouble as our oven is in our house on a small island in the Bahamas. We thought our choices were to either take the door back to the US have it repaired and then bring it back to the island (which could take weeks) or fly a repairman in at a cost of about $1500. By my good fortune, I found Parts Select when I did a google search for Jenair Ovens and the website walked me through how to find and order the part. It was FedEx'd and within 48 hours our door was back on and we had an oven again! Thanks so much!

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

Found parts on-line from Partselect and made the repairs very easily. The oven door now closes all the way, the oven light shuts off and the oven gets hotter quicker.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

first of all i was shocked at the fast delivery,two days .i just followed the instructions the other guys wrote,the only thing i might add is that the screws on the bottom of the door hinge are very tight you must have a good bit and line them up well, at first i did not think they would work but they did also you must replace the bracket as well as the hinge