JJW9627CAQ Jenn-Air Wall Oven - Instructions

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Shut of power to unit, removed front display panel, located lower circuit board. Removed the one screw holding existing board and installed new board, then swaped wires from damaged to new. re-installed front panel, turned pwoer back on, that was it. The unit is working well.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

The diagram on your website really showed me the part I needed. I had may part the next day and my son who is an IT man changed the part in under ten minutes.. I was very happy, because I thought I was going to have to get a new oven. I rely alot on timed usage.

Turned off power at breader box. Removed the glass face of the control panel. It was secured with 4 screws. The electronic clock was attached by four hex screws which were removed with a socket wrench. There are 4 electrical connections which must be removed and reattached to the new circuit board. They are keyed so you can't attach incorrectly. Reverse the order, turn the power back on and the LED's glow bright again. Unfortunately, the first part that was sent did not work. However, on the warranty placement a new part was sent right away. The turn around time was excellent, and the new part worked just fine.

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Ordered part on line, part came within few days well wrapped and protected, very simple repair removed two mounting screws and two lead wires to remove burnt element, replaced with new one, wire were re-connected and the mounting screws secured the new element in place, about 20 min job.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Removed two screws, pulled out element and trnasfered over lead wires. Made sure power is off first. Easy to order, easy to replace.

1. Shut off power
2. Removed 4 screws holding glass control panel
3. Unplugged 3 wiring connectors from back of control panel and removed it and laid on table.
4. Unplugged wiring connector from bad display board and removed it from control panel (2 snap tabs).
5. Installed new display board and plugged in wiring connector.
6. plugged in control panel wiring connectors and reinstalled with 4 screws.
7. Turned on power, and presto - bright new clock display! Piece of cake - 1 phillips screwdriver and 10 minutes. Anyone can do it. Thanks for a great site and all the postings - it helped me diagnose the problem and order the correct part with complete confidence.

Unscrewed 4 screws to remove the glass cover on the top of the double ovens. Unscrewed 4 screws holding the clock in place. Screwed the new clock in place, reinstalled the galss cover and screwed in the 4 screws.

One issue though is my double oven is 6 years old and I have replaced the clock twice, the last one lasted 2 years. Anyone know why this happens so fequently?