SVE47600WC Jenn-Air Wall Oven - Instructions

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

Removed old filter and replaced with new.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

My oven door would not close all the way and the hinge receptacle pins were bending over time even with new receptacles. I ordered two replacement hinge receptacles under warranty but they took so long to come, I had to make the door close to cook the Thanksgiving turkey. I used two rectangular magnets from a home goods store, and placed them in the top corners of the door. The door closes better than it did new, and no heat or cooking smells come out. I won't even have to change the hinge receptacles and it beats having to cut out the perpetually bending pins of the receptacles to replace them with stock # 8 steel bar and weld them in place. The magnets stay put. Easy!

My son put in the new part and turned on the oven. The broiler heated, but not the bake element. He switched the wires to find out if the bake element would work. It heated, but not the broiler. That told him the control board was a problem. He took it off and could see that one of the solder points had burned off in the explosion. He cleaned the board and put on a new dot of solder. He put it all together and it worked perfectly.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

This slide out range requires that you remove two screws that hold the element into the back of the oven, slide the range out, remove a metal cover, and then disconnect the two spade connectors from the element. Reverse is the opposite. I could not find the element anywhere locally. I live in a rural area of the Smokey Mountains. Thanks to PartSelect, I was up and running in only four days.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

5 min. to replace old with new. Remove 2 screws
and detatch wires. Re-attach wires and replace screws. PROBLEM -THE ELEMENT- I recieve had 2 wire legs which hold the element off oven floor, these legs were loosely to element and one came off during installation. OEM had large clamp on legs- I had to remove leg from OEM and attach to
element.( Hacksaw ,file ,vice)

ordered new broiler pan

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...