RK777G*D2 Hotpoint Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rosemarie from Saint Simons Island, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
the bake element burned
as you explained in the e.g.
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.
Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.
Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Exton, PA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt out
First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from Centennial, CO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out element
Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- c from Cincinnati, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element melted! Lucky it didn't start a fire!
The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Dallas, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The element in the upper oven burned out. Looked like a welder's torch when it went out.
After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.
The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
My part was delivered in 2 days regular UPS.
The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Wauwatosa, AL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old element burned out
Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Mena, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element brned out.
Removed two screws to release the burner, then two screws to disconnect the wiring and replace them. Then inserted the burner int position and replaced the two screws which were removed to remove the burner.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Pasadena, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke in several places
Turned off the power source to the oven. I then removed the two screws that hold the element in place, then pulled the element out about 3 inches and disconnected the two wires at the back. The hardest part was getting the screws turned to connect the new wires at the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Marietta, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baking Element not working
Repair was easy! I asked my son to take out the old and put in the new! He did! The oven works like new again for less than $50.00!!! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felicia from Little Rock, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bottom heating element in the oven was not heating
First I shut off power to oven. Then I removed two screws from the back of the oven. Pulled elemeent out a couple of inches and diconnected from the power source. I removed the old unit and replaced it with the new one. Connected it to power source. Pushed element back into place and replaced the screws. Turn the power back on and turned on the oven. ....And there was HEAT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out.
I removed the two screws that hold the element in place; pulled the element out, disconnected the two wires held on by screws, replaced the element with a new one and reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Flower Mound, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Beke Element broke into 3 pieces
followed the existing guidelines from this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from North White Plains, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken oven element
I removed the two screws that keep the element in place.Then I pull the element a little bit and disconnected the two wires and removed the old element. Then I reconnected the two wires on the new element then put the element back on position and put back the two screws that keep the element in place. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from two rivers, WI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
oven wouldn't heat eliment was burnt and sparking
took out old then put in knew
Was this instruction helpful to you?
Thank you for voting!