RGJ616GEH1 Hotpoint Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martin from Newport Beach, CA
- Parts Used:
- WB2X9998
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't light, burners worked fine (gas oven).
Unplugged the power cord from the oven. Unfortunately I couldn't figure out how to remove the broiler drawer so I didn't have a lot of room to work. Basically I had to unscrew one Phillips screw to remove the metal housing that shields the wiring and connectors from direct flame of the oven. Once I removed the housing it was a matter of removing 2 wire caps where the wires from the igniter spliced into the power source. Once the wires were disconnected, I unscrewed the 2 Phillips screws that attached the igniter to the mounting bracket and removed the old igniter. I had to cut the wires on the new igniter to the correct length and stripped the insulation so about 1/4" of bare wire was exposed to splice to the wire from the power source. I then attached the igniter to the mounting bracket (2 screws), twisted the wires together to connect to the power and attached the wire connector caps. I reinstalled the protective housing (1 screw) making sure the wires were clear and not being pinched. Plugged the power cord back in, turned the oven on and everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from TWIN FALLS, ID
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Lancaster, PA
- Parts Used:
- WB2X9998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Worn out oven igniter
Disconnect the power cord.
Lift the Oven door UP to remove it from the Hinges. Then unscrew the Nut/screw and remove the floor of the oven. Remove the broiler drawer. Remove the screws from the cover plate along the back wall of the oven where the wires go. Observe where the old wires go/went.
Cut the wire from the old igniter 3 : from the igniter .
Remove the old igniter from bracket with screwdriver.
Thread the new wire where the old wire went. Now Mount the new igniter to the bracket. Strip the old wire about 1" . Use Ceramic 'twist connectors' supplied. Plug in the stove and test the new igniter. When happy with the instillation, unplug the electric and allow the new igniter to cool. Finally, re-attach the cover plate on the back wall of oven, replace the broiler drawer and oven door. Congradulate yourself and have a beer.
Lift the Oven door UP to remove it from the Hinges. Then unscrew the Nut/screw and remove the floor of the oven. Remove the broiler drawer. Remove the screws from the cover plate along the back wall of the oven where the wires go. Observe where the old wires go/went.
Cut the wire from the old igniter 3 : from the igniter .
Remove the old igniter from bracket with screwdriver.
Thread the new wire where the old wire went. Now Mount the new igniter to the bracket. Strip the old wire about 1" . Use Ceramic 'twist connectors' supplied. Plug in the stove and test the new igniter. When happy with the instillation, unplug the electric and allow the new igniter to cool. Finally, re-attach the cover plate on the back wall of oven, replace the broiler drawer and oven door. Congradulate yourself and have a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kelly from Napa, AL
- Parts Used:
- WB2X9998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven would not fire up
First checked with my flash light to see what was not happening. Compared the part with your oven parts, figured it out from there! Removed the wire, then the igniter from the bracket and that was it,just replaced the part. The ceramic tips for the wires came in handy.Now I can cook my turkey.Not bad for a girl!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Gary, TX
- Parts Used:
- WB2X9998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven wouldn't light. It glowed but wouldn't light. I came on your site to order a different part but after reading posts by others with my same problem figured I would try this first. It worked!!
My husband did the repair so I really don't know, he unscrewed the old one and screwed the new one on. Probably a little more detail but it seemed that quick to me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from New Lenox, IL
- Parts Used:
- WB2X9998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The burner igniter would not light
Removed the door. Then, removed the oven floor panel, removed the 2 screws holding the igniter. Cut the wire leads from the old igniter, stripped and connected the new wire leads to the old using ceramic wire nuts (included with part). Connected igniter to mounting bracket using original screws. Re-plugged in range and checked the new igniter for lighting. OK on first try, so replace oven floor and tighten holding screws. Then replace door. Tried out oven on a Red Baron Pepperoni pizza. Excellente!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Burton, WV
- Parts Used:
- WB2X9998
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Igniter would light, but burner wouldn't light.
First I turned the power off going to the oven, safety first. Then I removed the broiler drawer from the oven so I could remove the bottom plate, that gave me easy access to the wires and igniter. I took removed the two screws holding the igniter in place, then removed the wire nuts from the wires. I then reversed the procedure. This took care of my problem, the oven lights easily now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Texas City, TX
- Parts Used:
- WB2X9998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would not lite
removed 4 screws cut 2 wires connected new igniter put screws back in DONE Works great and SAVED MONEY Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from Tulsa, OK
- Parts Used:
- WB2X9998
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Oven won't Light
Replaced igniter in oven, Removed 2 screws in oven floor and removed floor panel. Removed 3 screws to remove the whole flame pipe assy. Disconnected 2 connectors on the ignition assy. Replaced ignition assy. with the cheapest ignition assy. spliced the 2 wires with the connectors of the old assy. using the supplied ceramic wire nuts and re assembled. Part from dealer was $89.00 part from here was $39.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Prospect, VA
- Parts Used:
- WB2X9998
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not light but everything else on stove worked
removed lower cover off of buner area, then removed cover where igniter wires connected to circuite, removed two screws holding igniter in place, cut and spliced new igniter to old push in fasteners of old igniter, reinstalled igniter, and plugged in new igniter, reinstalled covers and panels, turned on unit and bingo back to normal and as good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!