RK746GP1 Hotpoint Wall Oven - Instructions

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

removed and replaced

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.

took the old ones out and put the new ones in their slots. No issues

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.

Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.

ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.

Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!

When i finally got the right part.It only took few minutes to screw in and it worked perfectly.Customer support was very helpful in finding the correct part.thanks

had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.

I removed the two screws holding the element in, pulled it out, and unplugged it. Installation was reverse of removal. It's just that simple.

After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pushed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe

Used nut driver, removed 2 screws and removed old element. Reversed procedure for installion of new part. Can't believe ordered part one day & recieved it next day. Fantastic service. Will definitely call company again.

Installation was really easy. Remove the old bake element, plug the new one in, took at most 10 minutes.