JT1000SF4SS General Electric Wall Oven - Instructions

Step 1, turn off circuit breaker, verify no power at the back of oven

Step 2, remove oven from wall/housing by removing 4 mounting screws, 2 on each side, just on the inside after opening the oven door...this was the most difficult part doing the repair on my own as the oven is a bit heavy...I was fortunate to have a old Workmate 425 work bench that folds/collapses, this allowed me to slide the oven out and drop down about 2 inches...reinstalling the oven I did have to use 2x4s to shim the oven level to slide it back in, with someone to assist this would not be necessary.

Step 3, remove covers to gain access to the blower and sensor

Step 4, remove the sensor

Step 5, install new sensor

Step 6, turn on the circuit breaker

Step 7, test the oven (success, Y, turn off breaker and reassemble all covers, install the oven, secure with the 4 mounting screws, turn on circuit breaker, test one more to ensure of proper operation...N, go to step 8

Step 8, turn off circuit breaker, reinstall original sensor

Step 9, remove blower

Step 10, install new blower

Step 11, turn on circuit breaker

Step 12, test oven, problem resolved, Y, go to step 13, N, continue troubleshooting.

Step 13, turn off circuit breaker

Step 14, replace all covers and reinstall oven, secure with 4 mounting screws

Step 15, turn on circuit breaker

Step 16, test, still operating properly Y, receive hugs and kisses from wife, N, do not make eye contact with wife, take dog for a long walk.

taking the oven out of the wall the most difficult part.. once you removing the sheet metal screws....be sure to take pictures as you dis-assemble putting back together will be easier. wait for correct part. second try they sent the correct part. put back together, test before putting back into wall.. big savings by doing it yourself.

TERRIBLE!!!!!!!
FIrst part arrived broken
Second part arrived broken
Third part arrived broken
Finally on the 4th try, the part arrived and was not broken.
I will NEVER again order parts from this company.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

watched repair video on disassembling oven door and replacing glass.
followed the video.

there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance.

I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.

replaced lights in refrigirator and freezer

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

I used a Trox bit to remove one screw, replaced the oven sensor and reinstalled the screw. The whole project took less than 5 minutes.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

Followed the directions!