JKS05T1WH General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- cornelius from Hollister, CA
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
plastic sockets in end caps for connection screws broke off
Very detailed repair instructions on internet made installation of new end caps a job not needing a professioal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Waco, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom baking element had burned out
I simply removed the two screws but the back of the element holding it in place and pulled the element out far enough to clearly see the wiring. (TURN OFF THE ELECTRICTY TO THE OVEN). Gently pull the snap connectors off the element leads and snap them on the replacement element, push wiring back into oven opening, tighten down screws, clean up and close the door. Turn electricty back on and start the oven. It will smell for a few moinutes while the element heats up for the first time. You are good to go. To Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgianna from Austin, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap broke on oven door.
It was easy as pie. Just followed the instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Freeport, NY
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower Bake Element Had Cancer-Like Freeakout!
Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Charleston, MS
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out bake element
I cut of electric braker in fuse box, unscrewed two screws and replaced element in less than five minutes, really easy task. Oven worked well. Thank you Park Select, good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Warwick, RI
- Parts Used:
- WB3X5699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knobs
remove and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from Dallas, TX
- Parts Used:
- WB48T10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing racks
took the old ones out and put the new ones in their slots. No issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from De Soto, MO
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left bracket broken on range oven door handle.
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portion of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from White River Junction, VT
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
New bake element
I am 68 years old and found that changing element was a breeze---using pliers removed nuts--unhooked bad element--rehooked new element---done------------recieved new element in 2 days--------- Thanks -----------------
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from South Bend, WA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.
The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from SUGAR LAND, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burned out oven element
Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Cogan Station, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken oven door handle. Needed the brackets and screws to repair it.
removed the broken parts and screwed on the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Muskego, WI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke end cap while moving range
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Decatur, IL
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element melted down
Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Los Altos, CA
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Oven broiler stopped working. Had to replace the broiler element.
Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.
Was this instruction helpful to you?
Thank you for voting!