JTP15WW1WW General Electric Wall Oven - Instructions

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

#1) Found electrical control breaker and moved to "off" position

#2) Removed two (2) screws with a nut driver, that were holding the bake element in position against the back wall of the oven. Gently pulled the original bake element out toward the door to expose the wire connectors from oven to element, then disengaged the connections.

#3) Removed the damaged element, replaced with the new element, reconnected the wires to the element, and returned same into the back wall opening and reinserted the two (2) screws with nut driver.

Repair was complete. Electrical breaker returned to on. Procedure Done!

Initially replaced thermostat sensor but unsuccessful. With some help from internet repair, the removal and replacement of the electronic board was easy given the labelling on the new board was essentailly identical to older model.

The first task is to turn off the breaker so there is no power coming to the oven. I learned in the hard way that even though the oven is turned off, there is still a hot wire connected to the bake element. Next,I removed the oven door and shelves. Then I used a nutdriver to remove the two screws holding the element in place. I expected to find a plug, however the element is connected to two wires buried in the insulation. I pulled the wires off of the bake element, connected them to the new element and put everything back together. This is not a difficult task.

First I unplugged unit. Theni removed the two screws that hold the element in place . Then went to pull the element out to disconnect the two wires,but was having alittle trouble. There for I removed the large plate(cover) on the back of range,and removed the wires from this location. Put the new element in place,reattached wires,screwed back plate back on ,and pluged back in.

Unscrew the old and put in the new.

I found that some of the wires were hard to remove, so I had to use a pliers. When it came time to install the new part, I found it easier to mark the wires by color on a piece of paper and their location from right to left as I was looking at it. To me it was to hard to try to hang on the panel and try to plug the wires into the new part.

Removed oven from wall. Door slides up and off, and 4 screws into cabinet removed, and oven slides right out onto a coulple kitchen chairs positioned to support the oven. 1 man job to lift. Used nutdriver to remove metal cover on bottom back of oven to expose the slide on electrical connection. Used nutdriver to remove old bake element and install new bake element. Reconnected electrical wires, reinstalled back cover, and then reinstalled oven into cabinet. I actually removed the internal metal cover over the convection fan and element also but probably didn't need to do that to remove and install the new bake element.

After securing the power, removed wires one at a time and placed them in the new controller. The new unit was slightly different at a couple connectors but both old and new boards were marked with alphanumerics and or colors.

Easily glide in.

removed twoscrews from rear of oven,undid two spade connections removed element.replaced with new one,thats it.

placed them in propper position we had been to apliance stores and told they would need to order them and it may take up to two weeks to get them. we ordered them from you and they were here in a matter of days, and the price was the best we had been quoted. thank you so much

I opened oven and pushed oven rack inside.

1. Switch electricity off at circuit breaker panel. 2. With a helper slide door off hinges and set aside. 3. Remove all oven racks. 4. Using socket wrench remove the two screws attaching element to back of stove. 5. Pull the element from the back of the stove and slide off the 2 electric bayonet clips from the old element. 6. Install new element attaching the new element to the old electrical clips. Note: You may have to crimp down the clips to keep them secure to the new element. 7. Reinstall element screws to back of stove using nutdriver. 8. Insert racks and slide door back onto hinges. 9. Turn back on electricity. 10. Turn on element and let it "burn in" for a few minutes. Note: There will be a slight smell while doing this.