JTP56AA1AA General Electric Wall Oven - Instructions

The thry was rusty I took the door out And i slide out the thry it's take five minutes I did it by myself now my oven Look like a new I'm so happy now I get the part quickly thank you

Very was ti replace racks and knobs. Very fast mail service

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.

twisted it in place

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Replaced new light housing.
Thanks to you guys for the prompt response

Shut off electrical breaker to oven Remove front control panel by removing screws in the upper oven. Disconnect wiring to remove panel make sure you tag/mark where the wire harness connects to the pan. Disconnect electrical feeds from motor. Remove 4 motor assembly mounting screws. (maybe tight but it can be done). Clean screen before installing new motor. I couldn't get the lower screw in, so only replace 3 of 4 screws. Reverse instructions by re-connecting harness(s) and control panned and ave screws. Turn on electric breaker. All good

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Quick and easy, thanks!

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

Replaced it

1. shut power off (if it is a built in you will have to go to the house control panel to shut the power off). To ensure that it is off check the clock light prior and after you throw the switch it now should be off. 2. remove screws holding ovens in cabinet should be 8 (Phillips)on the sides of the ovens inside, you have to have to have the doors open to remove 4 top and 4 bottom 3. slide ovens out of cabinet about 4 to 6 inches (do not pull on doors) open the bottom door reach inside of oven and slide to the left and the right while gently lifting. 4. close the bottom door and open the top door. above the door and below the control panel you should see at least 3 screws I removed them with a socket and ratchet, but you can use a wrench or adjustable wrench. 5. on top of the panel you should see two screws (Phillips) on one on each side. remove the screws. 6. The control panel has a small tab in the middle of it, you will now be able to lift the cover that the tab is slid into (tin this is the top of the oven) while you hold the tin cover up about 1/4 inch hold on to the panel tipping the bottom out this should release the tab and allow you to pull the control panel out. Now close the top door and the panel should rest on the handle of the door. 7. looking into the top of oven you should see two limit switches (they are round with two screws holding them down with two wires that slide on the tabs) One of these in my case the one on the right runs the fan while the one in the center runs the door lock. To determine if the switch is faulty remove one of the wires from one of the limit switches and either tape or use a clamp or even a paper clip so the wires on the same limit switch will be touching. 8. now carefully put the control panel back tipping the bottom out to insert the tab in the top cover and put in one of the screws to hold it in place. 9. turn on the power check to see if the door lock is working correctly and the door lock light is out. If it is not working and you hear the fan running then you have jumped the wrong switch. If this is the case shut the power off then return the wire back on the jumped switch and repeat the process with the other limit switch. 10. after you jumped the correct switch the door lock light is off. Check the system with the power on by putting the oven in the self cleaning cycle. The door lock light should start to flash and after the door locks it will stay on steady. Press the stop or off button the door lock light will begin to flash and when the lock is released the door lock light should go out. If the door has been pulled on or forced open the locking device can strip and will only go so far with out locking the door. You will then have to remove the locking device with the motor and replace the motor. With the switch jumped and everything is working then this is the problem shut the power off and replace the switch. Caution there are two limit switches in the bottom oven also one with a reset that is about $50 it is bigger and will not bolt down. The one that is in mine is smaller and cost about $23 make sure that you order the correct one shown in the diagram provided by Parts select. 11. reinstall the control panel should be 3 screws on the bottom and 2 on the top. Open the top oven door and carefully slide the oven back in place pushing on the sides do not push on the oven door. Attach the cabinet screws 8 turn on the power.

Easily glide in.