JT910CA3CC General Electric Wall Oven - Instructions

Replaced new light housing.
Thanks to you guys for the prompt response

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Quick and easy, thanks!

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

Replaced it

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Loosen top panel (3 srews). Remove limit switch (approx 1-inch diameter disk), after unhooking two wires and removing two screws). (Limit switch on left upper side. ) Replace limit switch and top panel.

Ordered new probe

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

plug in thermistor when needed

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

Pulled out old with pliers. Twisted new clips in per instructions.

I ordered the correct oven rack thru Part Select's customer service. They helped me get the correct part info. Once it came I slid it in the oven and viola it was a perfect fit!

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Feedback on site warned me that broiler element is only connected to oven wiring with press-on spade lugs rather than screws. Even with care I managed to 'lose' a wire and had to retrieve it with section of stiff coat-hanger wire bent into a hook. Coming off that experience, I soldered the spade terminals together before reassembly to avoid a repeat. New element, however, failed to rectify problem. Professional technician found main control unit defective -- a $300 part including installation, but at least GE still has it available. My advice to others in this situation is to remove old element before ordering a replacement, and test with meter to see if it's defective. It may or may not be worth going beyond an element replacement to you.