JKP27G*J4 General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jack from kenner, LA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
bottom element blown
1. isolate the main power supply. 2. remove backplate on old element,remove connecting terminals from old element; and withdraw from oven. 3. connect new element[make sure the connection is firm].replace backplate and secure with the two screws provided. switch on power, oven working perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Fountain Hills, AZ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven not heating after being on 45 minutes
A friend gave me your website. I looked up the model (is over 30 years old & obsolete!), but you listed a similar model. Part fit perfect, works great, heats to set temp quickly. Your do-it-yourself page was a big help...thanks! Replacement went quick and easy after I saw what needed to be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Andover, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element hot spots and deformed
Looked up mfg. and part #,looked at blow up of stove on parts select, identified element. The part came overnite. Shut down power, removed 2 screws with a nut driver, pulled element foreward to reveal 2 screws attaching wires. Replaced in reverse order, turned on power, back in service. 10 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Midland, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake Element Burned Out
It is simple.
Cut off the power. Remove racks. Remove burned out element and replace with new one.
Replace racks and turn on the power. Set the clock.
I've done this about 5 times and now keep a spare element.
Cut off the power. Remove racks. Remove burned out element and replace with new one.
Replace racks and turn on the power. Set the clock.
I've done this about 5 times and now keep a spare element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from TULARE, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burn out the Heating element
Removed burn out element,very easy to installed, screwed them in, done that fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from PLAINFIELD, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The heating element was broken in one place & wouldn't heat
Ordered the part on a Friday afternoon and was shocked to receive the box on Saturday AM! Turned off the power to the unit, unscrewed the screws holding in the old element, and hooked up the new one. We didn't have a socket wrench so we subbed a pliers. So easy & cheap! Seems like everything's breaking around this house & this is the ONLY thing that was easy & cost less than $20! Happy with Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Meridian, MS
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
240 Volt Bake Element Failed In Upper Oven
Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Silver Spring, MD
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
My 20+ year old bake element cracked
I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from Spartanburg, SC
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Heating Element
The bottom heating element burned out. Ordered the right part and my husband fixed the heating element. This saved a lot of money.Thanks, RM from South Carolina
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from San Jose, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Cal Rod heating element failed
Getting the part out was easy. Turned the power off (of course) first. The outside nuts were corroded, so had to use a pair of pliers to get them off. The inside connectors were easier to get off. I had a little trouble getting the connectors on the wires. The metal part on the heating element kept wanting to bend. I finally had someone hold that in place while I made the connections. The outside screws were easy to put on. The oven now works great. I think the element was failing over a period of time, and we just didn't notice. I can't remember the last time I actually saw the element get RED hot. Works great. Thanks for your quick service and reasonable prices. Will definitely use you again, when I need parts like this. (You are now Bookmarked on my computer).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Southfield, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Broken heating element
Turned off electricity at fuse box. Unscrewed old element and removed. Put in new element, screwed it in. Turned on electricity. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William M. from Towaco, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element went dead
Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Mena, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element brned out.
Removed two screws to release the burner, then two screws to disconnect the wiring and replace them. Then inserted the burner int position and replaced the two screws which were removed to remove the burner.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Roseville, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace baking element
Turned off power at breaker and removed old element and replaced new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Venice, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replace Burned-out oven bake element
Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!