JKP26GT1BB General Electric Wall Oven - Instructions

As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman

We removed the two very tiny screws that held the plate through which the element was connected to the wiring. It was extremely difficult to do so, because the screws were so tiny. Our socket set did not have such a small attachment, and we had to use an adjustable wrench. Once we accomplished that, we unhooked the old broil element from the wires. At that point, the wires snapped back into the wall. There was almost no slack to pull the wires back out into the oven so that we could hook the new broil element up. It took more than an hour of maneuvering before we were able to get hold of enough of the wires so that we could grab onto each one and hook up the new broil element. One we did that, it was easy to place the broil element back into its brackets.

From what I was able to find info on I was to take out 5 screws 3 on top and 2 on the bottom then the inner oven box is suppose to pull out a bit to take the old gasket off and put the new onw on the box was so rusty it would not pull out so I was able to get enough of the box out using a large screwdriver the lip of the gasket tucks behind the box. I ended up using a small screwdriver to work the new gasket behind the oven box. The door now needs new springs the tension on them is not strong enough to pull the door shut the way it should there's still room to push the door into new gasket.

Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.

Drilled small holes in blades to accept existing machine screws from oven wires.

My husband (a retired tool & die maker) easily removed the old bake element after first turning off the circuit. He cleaned up the burned salt that we had used to try to put the "fire" out but finally just shut down the circuit. Then just as easily istalled the new element. Thanks to your quick service, we were only without the use of the oven for a day and a half!

removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws

Unscrewed three screws from each oven door. Unbolted the end pieces and replaced with new ones. Reinstalled oven door screws. Nothing to it.

This is a simple repair of the PS249249 UPPER BAKE ELEMENT requiring only a 1/4 in nut driver or socket wrench.

1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.

Make sure not to remove any insulation.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!

Turned off the power at the panel and then simply removed the two hext screws and unplugged the old element. Plugged in the new element and used a nut driver to relpace the two screws.

popped the new one on!