JTP27BA1BB General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from Thornton, CO
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven lights were burning out regularly
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from battle mountian, NV
- Parts Used:
- WB48T10095, WB49K2, WB48K2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing parts
placed them in propper position we had been to apliance stores and told they would need to order them and it may take up to two weeks to get them. we ordered them from you and they were here in a matter of days, and the price was the best we had been quoted. thank you so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- annie from san diego, CA
- Parts Used:
- WB57T10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke the bottom glass door with a chair
I unscrewed the four bottom phillip screws to loosen the rail where the glass sits. Then I loosened the two side screws that hold the door handle and I was able to move the upper rail just enough to be able to slide the glass panel where it goes. I then aligned the glass panel making sure it was secured on the bottom and upper rails. I put back the screws and tighten them to keep the panel from moving. It was a very simple part to install. Thanks for your quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Clarkston, MI
- Parts Used:
- WB44K5018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The lower burner element broke / burned out
After turning off the electricity, remove the inside rear panel over the fan by removing 4 screws, remove the 2 screws holding in the old heat element. Unscrew the unit from the cabinet by removing 4 wood screws on the front sides. Pull the unit out of the cabinet, I slid it onto 2) 4 x4 pieces of wood to make the reinstall easier. Remove the lower black panel on the outside back, it should have 2 screws and it slides into 2 notches on the back. The back of the element electrical tabs are exposed, pull off the 2 electrical connectors. From the inside carefully pull out the old element, slide the new one in the same space and secure with the 2 screws removed earlier. Attach the 2 electrical clips to the electrical tabs exposed in back and replace the metal cover. Slide the oven back into the cabinet, replace the interior back panel as it was removed and secure the front screws back into the cabinet. Turn on the power and test !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert H. from Lawrenceville, GA
- Parts Used:
- WB44T10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Double oven, top quit heating.
Replaced lower heating element by first turning off power at breaker box. Secondly, removing the two 1/4 " screws and slowly pulling the element forward exposing the two connections. Pull the element gently until you separate the heating element fromthe clips.Gently insert the new element into the clips and replace into the oven housing and secure with the two 1/4" nuts. Turn power on at the electrical box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Redding, CA
- Parts Used:
- WB23X5340
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
oven continued to get F2, F3 and F5 error messages when ovewn got hot
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Orlando, FL
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Clips needed to re attach heating element
Pulled out old with pliers. Twisted new clips in per instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!