JRP24BW5BB General Electric Wall Oven - Instructions

Removed mounting screws and element only pulled out about 2 inches. Disconnected wires and had to drill slightly bigger hole in element ends to reattach wires. Element mounting bracket was different than old element. Had to use one existing screw hole in oven back and drill a new one.

Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Truned off the power took out the two screws holding the old element disconnect the power leads and put in the new element. Was great to recieve the new element in one day, the day before Xmas.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

The repair was remarkably simple. Had i a nut driver, it would have been simpler still. Nonetheless, I managed to remove the nuts affixing the element to the back of the oven with a wrench, pulled out the old element, reattached the wires (they slipped in with ease), replaced the element, tightened the nuts and, presto, I was done. I suspect I saved over $100, though would rather my wife not know for fear it will be spent elsewhere;-)

Removed screws holding old element; removed back panel. Attached new element with old screws and replaced panel.

The entire element was replaced. Since the oven is proably older than me (about 30 years) the holes did not light up exactly so 2 new holes had to be drilled. It is working great now and I'm happy to find a part that works.

Be sure to flip the breaker to the oven to the OFF position before doing anything. Take out the two screws at the back of the oven that hold the element. Carefully pull the element forewarn to expose the connections to the wires. Disconnect the element from the wiring connectors. Be careful not to damage the connectors or the wiring. Plug the new element into the wiring connectors. Make sure you have the connections firmly in place. Push the wiring and connectors back into place. Replace the two screws. Make sure the element is resting in the spacers that keep it the correct distance from the top of the oven. Flip the breaker to the ON position, Turn the oven on Broil. The element should start turning a bright red. some fumes will come off the element. That is just oil from processing and handling. Your done!

Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.

I attached the end caps to my existing handle, but had to squeeze the parts together very hard to get them to mesh to the correct distance of the holes. I removed the screws holding outside frame of the oven door. I then opened the door fully, propping it up on my knee and removed the inside end cap screws. Placing the handle in position underneath the propped door, I attached the screws. Lastly I reassembled the door.

just replace the end cap with a new one all that was involue was to screw the new one in took about ten minutes and job done better than buying a new stove when the stove is still just like new. thank you for your on line help.

I pulled the old broiler from holding clamps. I unscrewed the 2 screws holding the old broiler, pulled it out very slowly while using clips to hold the wires from going back into the wall behind the oven. That’s very important, I then pulled the old broiler off and replaced the new one. First I secured the elements on the oven clips that hold the element up, I reattach the new element, screwed the 2 screws back in. DONE My grandson helped, total time, maybe 15 minutes. Watch their video. Really easy, save money.

switched off power to oven, unscrewed old broiling unit and installed new one.

First I removed the two screws that hold the element in place. I then pulled the element out disconnected the two wires. THE PROBLEM IS THAT THERE IS HARDLY ANY WIRE TO WORK WITH. Otherwise I would have been finished in ten minutes.