JKP56AA1AA General Electric Wall Oven - Instructions

Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D

It's so simple most people could mannage the repair. Turn oven off. Remove oven door and shelves. Use a nut driver to remove mounting screws. Pliers to pull quick connect terminated wires off element terminals. Use pliers to push connectors onto new element,wires may connect to either terminal. Nut driver for screws to mechanically mount new element. Replace shelves and door. First time element gets hot it will burn off oils and dirt, not a problem but do it now not later.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

1) TURNED OFF THE POWER TO THE OVEN. 2) REMOVED THE TOP DOOR AND RACKS. 3) REMOVED THE 2- 1/4 HEAD HEX NUTS AND PULLED THE ELEMENT FORWARD ENOUGH TO EXPOSE THE ELECTRICAL CLIPS TO THE ELEMENT. REMOVED THE CLIPS WITH A PAIR OF NEEDLE NOSE AS ADDED GRIP. 4) PUT THE WIRE CLIPS ON THE NEW ELEMENT AND REVERSED THE ABOVE PROCEDURES.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping

[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.

[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.

ordered parts WB21X5301 oven sensor and 2 WB1X681 screws mine were bad highly recommended slid my stove out also a good time to clean all the years of junk behind it removed screws mine were bad unplug the connector slide the sensor cable through the hole and u are good after cleaning be hind stove slide back into spot reinstall power and code went away tested different temps with temp gauge and keypad and we were good

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

First I removed the two screws that hold the element in place. I then pulled the element out disconnected the two wires. THE PROBLEM IS THAT THERE IS HARDLY ANY WIRE TO WORK WITH. Otherwise I would have been finished in ten minutes.

Quick and easy, thanks!

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

it was real easy, I just watched my husband do it!