JTP27WA3WW General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marion from METHUEN, MA
- Parts Used:
- WB2X9719
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Single Heating Element Support Clip was needed to hold up the heating element in the oven. Old single heating element support clip broke and came out of the hole.
Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lloyd from lorena, TX
- Parts Used:
- WB26K5061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Lots of fan noise with f2 error code when oven on
Made triple sure electricity off. GE designed excellent access to box above oven. Remove three bolts above oven door on bottom of control panel. Slightly raise panel to take off control panel, let hang by wires. Fan in back wall behind panel and has two wires that unplug, four screws to remove. Plug in new fan, input 4 screws. Partselect excellent guide to make sure correct part was ordered, and very timely delivery. $85.00 part instead of $1500.00 new oven. Tip - Note that fan burns out when auto clean turned on. Stop doing that and problem doesn't repeat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Rio Vista, CA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Rome, GA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Element was fried, no pun.
Exactly as you descibe and after disconnecting the two wires from the contacts on the element and taping the two wires to the oven wall so they do not fall back into the hole from where they came was extremly helpful. Also was an opportune time to clean the oven properly prior to installing the new element.
Thanks
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gansevoort, NY
- Parts Used:
- WB08T10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CUMMING, GA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from BELLEVILLE, NJ
- Parts Used:
- WB14T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Left hand hinge was broken, oven didn’t close properly.
I remove four screws two on the left side and two screws on the right side. I pull the oven out about ten inches, removed two screws that hold the hinge in place, took out the broken hinge and reverse the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ian from brevard, NC
- Parts Used:
- WB44T10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element broke
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) Then I simply re-connected the replacement element and viola!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SALISBURY, CT
- Parts Used:
- WB2X9719
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The old single heating element support clips came loose over time.
I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Hilton Head, SC
- Parts Used:
- WB24T10147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burnt Smell
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hedgesville, WV
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element clap broke off
All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kurt from Novi, MI
- Parts Used:
- WB26K5061
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
Oven over heat sensor in upper control compartment going off due to circulation fan failure.
Turn power to oven off at the breaker.
Remove access panel to upper control panel.
With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.
Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.
Remove access panel to upper control panel.
With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.
Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Falls Church, VA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old blackened oven racks
Replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Frederick, MD
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Oven Light Assembly damaged
I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
Was this instruction helpful to you?
Thank you for voting!