JRS04BW6BB General Electric Wall Oven - Instructions

Although the parts did fit, some modification was needed to remove the excess tabs as it appears these parts were for multiple applications. However the end result was a good fit and reapirs were successful.

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping

[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.

[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.

Removed mounting screws and element only pulled out about 2 inches. Disconnected wires and had to drill slightly bigger hole in element ends to reattach wires. Element mounting bracket was different than old element. Had to use one existing screw hole in oven back and drill a new one.

Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.

Truned off the power took out the two screws holding the old element disconnect the power leads and put in the new element. Was great to recieve the new element in one day, the day before Xmas.

Shut off the power from the fuse box. Removed p the two screws and plate that attach the element to the wires and back of oven. Installed the replacement element by attaching the wires and reinserting the two screws. Restored power and tested the new element by preheating the oven at 350 degrees and letting it heat for 15 minutes. Works like a charm!

just replace the end cap with a new one all that was involue was to screw the new one in took about ten minutes and job done better than buying a new stove when the stove is still just like new. thank you for your on line help.

ordered parts WB21X5301 oven sensor and 2 WB1X681 screws mine were bad highly recommended slid my stove out also a good time to clean all the years of junk behind it removed screws mine were bad unplug the connector slide the sensor cable through the hole and u are good after cleaning be hind stove slide back into spot reinstall power and code went away tested different temps with temp gauge and keypad and we were good

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.

The repair was remarkably simple. Had i a nut driver, it would have been simpler still. Nonetheless, I managed to remove the nuts affixing the element to the back of the oven with a wrench, pulled out the old element, reattached the wires (they slipped in with ease), replaced the element, tightened the nuts and, presto, I was done. I suspect I saved over $100, though would rather my wife not know for fear it will be spent elsewhere;-)

The entire element was replaced. Since the oven is proably older than me (about 30 years) the holes did not light up exactly so 2 new holes had to be drilled. It is working great now and I'm happy to find a part that works.

I attached the end caps to my existing handle, but had to squeeze the parts together very hard to get them to mesh to the correct distance of the holes. I removed the screws holding outside frame of the oven door. I then opened the door fully, propping it up on my knee and removed the inside end cap screws. Placing the handle in position underneath the propped door, I attached the screws. Lastly I reassembled the door.