JT915BF5BB General Electric Wall Oven - Instructions

Circuit breaker off. Watched You Tube video to easily remove and set aside oven door, and shelves, unscrewed back wall cover over convection heating element, and slid out cover over floor heating element. Used ratchet to easily disconnect both old heating elements & pull from rear wall, holding onto two clip electrical connectors while gently pulling out plenty of slack as wires fed through insulation material. Concern of "losing" wires back into oven wall not truly a problem if careful. Both sets of connectors pulled off, easily and then slid onto replacement elements without trouble. Circular convection element screwed back into place and cover replaced. Replacement floor element was similar, but not identical, to original. Wires connected fine, but base plate and two screw holes to attach to rear wall were of different size. It rests underneath oven lower cover on its own feet, so really didn't require support. Being DIY obsessive, I nonetheless used its base plate as template to drill two new holes in oven back, secured with old screws. Replaced cover, shelves, door, and woking like new!

First, I turned off the power. I removed the fixture that held the bulb and gently used narrow type pliers to pull the old pins out and allowed the broken glass to fall upon a shop towel in the bottom of the oven.

The replacement bulb and different type of wiring connections. I cut and formed them to fit the receptacle. I gently inserted the new bulb, placed the glass cover back on. Then, screwed the unit back into the top of the oven.

Happily, when power was turned back on the light shone brightly!

RE: 2 yr. old GE double wall oven with convection option in upper oven, non-convection in lower oven: baked goods were not browning, were undercooked or burned. Tested both ovens on regular bake setting using 2 oven thermometers. Set ovens for 350. Although after 10 min both ovens beeped "ready", the oven thermometers actually read 200 - then would swing up as high as 500 and as low as 200 during the 20 min test period. Decided to first replace top oven sensor only, just in case it really was a more expensive control panel problem. It was a bit awkward to reach back there with the oven door in the way, but I have long arms! Aimed my flashlight, removed nuts with a socket wrench, pulled out the sensor, popped the clip and the old sensor easily separated from its connection. Snapped on the new sensor, pushed it back in and reset the nuts. Easy. Set the oven for 350 and tested again with 2 oven thermometers for 45 min. Voila! The oven thermometers read exactly 350 when the oven beeped "ready" and it stayed at 350 throughout the entire 45 min retest period with only a 3 degree variation both up and down. What a great improvement! Immediately went online to Parts Select and ordered another sensor for the bottom oven which was having the same problem. Fixed both ovens all for under $30 - and just in time for Christmas cookies! Don't want to know what the repair guy would have charged.......Merry Christmas!

The oven lamp shattered while cleaning. Easy to replace by hand.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Removed back panel, change out sensor

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.

Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!

Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.

Replaced it

plug in thermistor when needed

turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.