JCKS05BA3BB General Electric Wall Oven - Instructions

popped the new one on!

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

By myself

Followed the instructions

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

I counldn't get the nut screw out. It wounldn't turn. Had to call a technican.

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

Turned off power to oven. Lifted off the oven door. Removed four 1/4 " bolts from outside of fan housing. Removed two 1/4" bolts holding element. Removed element from three clips holding it to upper oven surface. Unplugged two element wires. Reassembly was the reverse. I am an auto mechanic by trade and this was a fairly simple process.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

I thought because the broiler was off that I could remove the element with not problem. As I was pulling the element out, it sparked, melting something in the back I couldn't see at the time. I immediately went to the breaker box and turned the power to the oven off. After I found the website online I was very gratified to see how easy it was to identify the element I needed and order it. I removed the old element. One of the wires from the element slipped through the hole in the back of the oven. To get at it I had to unscrew the four screws around the outside edge of the oven and pull the whole oven out. I had a table handy that I pulled up next to the oven and set it on without disconnecting the main wiring. After getting the oven out I removed the six or so screws on the coverplate and easily found the loose wire. I pushed the wire back through the hole in the back of the oven and made sure it would not fall back into the hole. I put the back plate on with all its screws; pushed the oven back into its hole and screwed the four screws in around the edge that hold the oven in. Then I attatched the broiler element to the spade connectors and screwed it back in place. I turned the breaker switch back on and tested it. It works.

took the old ones out and put the new ones in their slots. No issues

After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worked once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.