REGS36BCH0 Frigidaire Wall Oven - Instructions

I figured that it could not be a hard repair, that these things "die" in the ordinary lifetime of an oven, so that they would not make it too hard to get to. I pulled out the oven and disconnected it; opened three screws on the back, took off the back plate, and you could easily see the two connectors to the element. They came off with a gentle tug with pliers. Then you open the oven, and remove one screw on each side where the element is connected to the back wall of the oven. A magnetic hex socket end for the screwdriver makes it easier. Remove the old element gently through the glass wool insullation, and insert the new one with the element "legs" down. Verify the placement of the element connections in the back, and then replace the screw that hold the tab on the base of each element side to the back wall of the oven. Then, carefully reconnect the connector sleeve onto each end of the element in the back of the oven snuggly. Close the back panel with the three (the forth on the top was not tight and didn't need openening or closing)screws to the sides and bottom of the panel. Replace oven and reconnect to power, and test the element. It all took less than half an hour.

Just removed nuts. Pulled out the element from the unit. Disconnected each end. Reconnected new element. Pushed piece back into insulated unit. Attached nuts. Done.

They don't make appliances this easy to repair anymore. just as others say: screw out, unhook element ..hook new one to wires, screws back in.. you're DONE.. Thanks for great service and very quick delivery

took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.

I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.

Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.

Just took the back of the stove off and removed old one and put new one in. Very simple.

Removed back of stove, removed screws holding old element. attached new element in same place, returned back to stove. My wife pushed element from inside stove into holes, which was a help. Voila! It works great.

My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!

Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.

First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Removed the elments2 screws, unhooked the two wires, removed the rear cover from back. I then installed the new element, covered the termanals with electric tape replaced the rear cover screwed down the new element, tested.