BFES368EC7 Frigidaire Wall Oven - Instructions

Unsrewed side plates and removed old hinge and replaced with new. Recomend doing both left and right hinges or door will not close square.

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

I removed the element, plugged in the new one and that has corrected the uneven oven temperature.

Turned off electrical breaker (double). Removed the switch handle, removed the plastic rings (special wrench) under the handles. Removed three screws up under the front of control panel. Removed six screws holding the infinite switches. Removed defective switch. Different from the new switch. Wiring locations were different on the old sw. The reason for the vom use. All is well.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Found a YouTube video similar to the required repair. Took door off, disassembled the door, replaced the right hinge-spring assy, reassembled. Worked great. High quality replacement part from Part Select that was made in the USA.

I went to you-tube and found a video that told me how to remove and expose the hinge. That was all I needed. One stubborn screw was all the problem I had and it was replaced. Thank you for saving me lots of money!! It's working great and I would buy from Part Select again!

Husband/wife effort. We located our manual for removing the door and followed instructions. (It's probably online as well.) With the door off, we removed the screws on the side with the defective hinge, took out the old hinge and put in the new one. In trying to replace the door, we couldn't get the lock (upside-down u-shaped piece on the hinge) to rotate over the hinge lever hook on the new hinge. It looked slightly different than the other side (had a bit more hook on it that was in the way). PartSelect sent a new hinge in case the other was defective. (The first arrived in 2 days; the second in 3. No extra charge. Very pleased with the service!) Same trouble. So we filed off the tip of the hook and were able to move the lock in place and put the door back on. The door is not heavy anymore, but doesn't pull in tightly at the top. We thought about taking it off again and trying to position the new hinge a little better to see if it will fit perfectly (it slants down a little compared to the other side.) But it's not so loose at the top that the oven light comes on, so it's usable the way it is. And it looks good, so we're leaving it.

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.

Replaced both springs. Follow instructions in owners manual on removing door. Spring assembly resides in door. Remove screws holding spring assembly in place, then the remaining screws holding the inside of door in place. Raising the side, slide out old spring then slide in the new one - do the same on the opposite side. Replace all the screws - starting with those that hold the spring assembly making sure the latches are straight. Put the door back on making sure to lock "spring locks" detailed in owners manual