KF350GDF3 Frigidaire Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marla from Hibbing, MN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Element burned out
The wire on one side was stuck in the hole in the back and had to take the back off. It was easy to find and push through. I just connected the two wires to the new element and all was well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Overland Park, KS
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
inconsistent temperature
At first I used a nutdriver to remove the two inside screws and found that one of the wires were not long enough to disconnect. I had to remove an access panel in the back which only had 5 screws to remove. I took it off, replaced the element and put it all back together. Then my wife tested it by baking an angel food cake which turned out perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Independence, KS
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The lower heating element in the oven did not work
I ordered a replacement heating element for the bottom of the oven. All I had to do was to remove one screw on each side holding the element in and supposedly pull the element out to expose the spades on each end to unplug them and plug the new element in. As I did that, I touched the metal case of the oven and welded the spade off of the old element. I couldn't pull the old element out into the oven. First lesson---unplug the stove before doing this! I think that the reason I couldn't pull the rods of the element out into the oven is because they were tangled in the insulation. I then took the back of the stove partially off, pushed the rods out the back holes to expose the spades. The one that was melted could still be pulled out, so then I just plugged the wires to the spades on the element, pushed them back and put the screws back in on the inside. Another tip would to have a screwdriver that fits well. These were really tight, and you could strip the heads of the phillips slots. Anyway, the stove works fine. I could have pulled the elements with the wire into the oven, but since I had a welding job because I didn't turn the electricity off, it took me longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WAYNESVILLE, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Stove wires were not long enough.
Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Cumberland, MD
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
burnt core
remove old replace new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Shelby, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake element was broken
Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from Liberty, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The baking element burned in to.
Received the order the next day. Unpluged the stove from electricity. Used a 1/4 craftsman wrench to undue the screws. Pulled the old one out and disconnected the conection. Reconnected the new one. Pushed back in place, then re-tightened the screws. Thanks for having it in stock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Mineral Point, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
stove started smoking and sparks was coming out under stove.
The repair was pretty easy with the help of your on-line diagram. Other than the fact my husband failed to turn off power to the stove. Needless to say he got a small shock by the stove, Once he turned off power it went fast and safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Pittsford, NY
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not heat foods, low temperature.
The PartsSelect site provided the hint that the baking element might be the root cause of low heat. SO I order the part, got it within a few days and installed it. Simple matter of removing a small read cover and tow faston connectors to the heatng element along with two Phillips screws that secured the heating element. Oven now works like new!! Thanks PartsSelect, you saved me a bundle!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lincoln G from Jupiter, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Bake oven failed to heat due to break in element
Unplugged stove. Removed oven racks. Using 1/4" nut driver I removed two screws from back wall of oven that were holding bake element in place. Pulled stove from wall, removed lower back panel. Disconnected electric saber connectors. Pulled old element from oven. Put new element in oven. Reinstalled the two 1/4" screws. At the back of the stove, I reconnected the two push-on saber connections. Replaced back panel. Pushed stove back in place. Plugged in the power cord. Checked oven. Works fine.Great experience with Parts Select in every way.Total work time: about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Hialeah, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rotted
Husband replaced quickly no problems. This was the first time I have ever received a order so quick...(awesome service)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eleane from CLERMONT, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
my baking element broke in half in my oven.
I ordered the new part and looked online how to repair it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from St Clair Shores, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element fell apart
Easy! Unscrewed two screws, removed old element and replaced it with new one, then put back the two screws. Saved on a service call. Nothing could have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from West Bend, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
replace oven coil
unscrewed 2 screwes. very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from SALMON, ID
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No Heat
Remove defective element and replace with new heating element, bench checked servicable.
Was this instruction helpful to you?
Thank you for voting!