RGC32BAW1 Frigidaire Wall Oven - Instructions

took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner

Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.

Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a pair of pliers do to the tight fit. Removed the old element and set the new one in place. Connected the two wires to the new element and squeezed the connectors tight. Push the element and wires back into the original position and used the new screws to secure the unit to the stove back. Took all of 5-6 minutes. Tested the oven with an oven thermometer at 250, 300, 350, 400 and 500 degrees and and all read within 5 degrees of the settings. Very easy, very simple, very quick.

Thank you for the quick responce and fast delivery of the parts.

Chuck Wells

Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.

The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.

First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.

It was really easy. Removed the racks, removed the 2 quarter-inch screws with a nutdriver. Pulled the bad element out about 3-4 inches, enough to unhook the wires attached to the element with spade connectors. Unhooked the wires and removed bad element. Hooked up new element and reversed the process. Thanks PartSelect!

Just took the back of the stove off and removed old one and put new one in. Very simple.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

I just followed the instructions that I found online.