KF350GDH3 Frigidaire Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- THOMAS from WAYNESVILLE, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Stove wires were not long enough.
Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Shelby, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake element was broken
Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lincoln G from Jupiter, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Bake oven failed to heat due to break in element
Unplugged stove. Removed oven racks. Using 1/4" nut driver I removed two screws from back wall of oven that were holding bake element in place. Pulled stove from wall, removed lower back panel. Disconnected electric saber connectors. Pulled old element from oven. Put new element in oven. Reinstalled the two 1/4" screws. At the back of the stove, I reconnected the two push-on saber connections. Replaced back panel. Pushed stove back in place. Plugged in the power cord. Checked oven. Works fine.Great experience with Parts Select in every way.Total work time: about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from GRAND SALINE, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Burned Out
Took door off and remover racks. . Then took a nut driver and took the two screws out pulled element out and unpluged it from the wires. . . Then put the new element in place attached the wires and reinsalled the two screws. . . And I was done. . . Ready to rock and roll. . . . . Thanks to insructions from parts select very easy. . . . Thanksguys. . . . . . Ralph from texas. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Efland, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom burner not working
I just watched the video, unplugged the stove, attached the burner and started baking again. DSC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from Liberty, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The baking element burned in to.
Received the order the next day. Unpluged the stove from electricity. Used a 1/4 craftsman wrench to undue the screws. Pulled the old one out and disconnected the conection. Reconnected the new one. Pushed back in place, then re-tightened the screws. Thanks for having it in stock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Cumberland, MD
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
burnt core
remove old replace new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Overland Park, KS
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
inconsistent temperature
At first I used a nutdriver to remove the two inside screws and found that one of the wires were not long enough to disconnect. I had to remove an access panel in the back which only had 5 screws to remove. I took it off, replaced the element and put it all back together. Then my wife tested it by baking an angel food cake which turned out perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marla from Hibbing, MN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Element burned out
The wire on one side was stuck in the hole in the back and had to take the back off. It was easy to find and push through. I just connected the two wires to the new element and all was well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Mineral Point, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
stove started smoking and sparks was coming out under stove.
The repair was pretty easy with the help of your on-line diagram. Other than the fact my husband failed to turn off power to the stove. Needless to say he got a small shock by the stove, Once he turned off power it went fast and safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Hialeah, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rotted
Husband replaced quickly no problems. This was the first time I have ever received a order so quick...(awesome service)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Pittsford, NY
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not heat foods, low temperature.
The PartsSelect site provided the hint that the baking element might be the root cause of low heat. SO I order the part, got it within a few days and installed it. Simple matter of removing a small read cover and tow faston connectors to the heatng element along with two Phillips screws that secured the heating element. Oven now works like new!! Thanks PartsSelect, you saved me a bundle!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Fredericksburg, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bake element had burned through at a point near the right connect point.
I removed the old part, went on your website and found the proper replacement part ordered it and received it the next day. Two screws and the new part was in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randolph from Merced, CA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Oven element burned out
Removed oven racks; removed the two hex head screws holding the element in place; disconnected the two wires that attach the element to the range. Attached the two wires to the new element; replaced the two hex head screws; replaced the oven racks; tested the element. The whole process took about 10 minutes!! And it's something I haven't done before!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Saint Louis, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven would take 45 min to heat to 425
The repair worked GREAT! It took less than 10 minutes and now the oven heats to 400+ in 5 minutes...the element came via regular shipping in 3 days. We were ready to buy a new slide in unit for 1000.00, now we have a 23 year old oven that works better than when it was new!! All for around 30 dollars. THANK YOU!
Was this instruction helpful to you?
Thank you for voting!