REGS38BDW0 Frigidaire Wall Oven - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.

took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner

Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.

Removed 2 rear screws. Pulled out element. Popped out 2 wire clips. Replaced old element with the new one and attached wire clips. A caveman could do it.

I just followed the instructions that I found online.

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

remove old replace new

I ordered a replacement heating element for the bottom of the oven. All I had to do was to remove one screw on each side holding the element in and supposedly pull the element out to expose the spades on each end to unplug them and plug the new element in. As I did that, I touched the metal case of the oven and welded the spade off of the old element. I couldn't pull the old element out into the oven. First lesson---unplug the stove before doing this! I think that the reason I couldn't pull the rods of the element out into the oven is because they were tangled in the insulation. I then took the back of the stove partially off, pushed the rods out the back holes to expose the spades. The one that was melted could still be pulled out, so then I just plugged the wires to the spades on the element, pushed them back and put the screws back in on the inside. Another tip would to have a screwdriver that fits well. These were really tight, and you could strip the heads of the phillips slots. Anyway, the stove works fine. I could have pulled the elements with the wire into the oven, but since I had a welding job because I didn't turn the electricity off, it took me longer.

Unscrewed and unplugged old element, then put new one in it's place. Quick delivery and satisfied with DIY job.

Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.

Unplugged stove. Removed oven racks. Using 1/4" nut driver I removed two screws from back wall of oven that were holding bake element in place. Pulled stove from wall, removed lower back panel. Disconnected electric saber connectors. Pulled old element from oven. Put new element in oven. Reinstalled the two 1/4" screws. At the back of the stove, I reconnected the two push-on saber connections. Replaced back panel. Pushed stove back in place. Plugged in the power cord. Checked oven. Works fine.Great experience with Parts Select in every way.Total work time: about 20 minutes.