FEB500BABC Frigidaire Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vincent from Bonita Springs, FL
- Parts Used:
- 318036310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs for the three timers on the appliance console deteriorateddue to age.
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from TEMPE, AZ
- Parts Used:
- 318255101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Oven wasn't baking; broiler was OK.
1. Switched the oven power off.
2. Tried unscrewing the two screws in the rear of the oven but they were
too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires.
4. Attached the two wires to the new bake element and fastened it
with the two screws.
5. Switched the oven power on.
6. Tested the oven with good results!
2. Tried unscrewing the two screws in the rear of the oven but they were
too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires.
4. Attached the two wires to the new bake element and fastened it
with the two screws.
5. Switched the oven power on.
6. Tested the oven with good results!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cherilyn from W HOLLYWOOD, CA
- Parts Used:
- 318345216
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No instructions needed
Just slide the rack into the oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BIG SPRING, TX
- Parts Used:
- 318255101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking heat element burned out
Removed oven racks removed 2 screws & pulled the element forward & disconnected the old element by wiggling the snap on connecters put in new element connected the snap on wires pushed it back in place & put both screws back in done in 10-15 minutes ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryJean from Oregon City, OR
- Parts Used:
- 5303202116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken oven door seal
The part was very intuitive to install. First, we used pliers to remove the old metal clips and broken seal from the inside of the oven door. Second, we pressed the new clips into the holes on the inside of the door. The clips are preinstalled on the seal, making alignment with the holes easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!