CE6898VVV Crosley Wall Oven - Instructions

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

I took the broiler pan out of the shipping container and put it in the oven.

I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.

First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.

First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.

I first shut off the breaker to the stove - safety first!

I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!

The part came quick and packed very well. I moved the stove out and un pluged it. opened oven door and took a philips screwdriver and took the screws out at the back of element..Slid it out with the two wires attached and unpluged the conectors. pluged the conectors on to the new element and slid it back in. Had a chocolate cake in 35 minuts.
Thanks, John in Texas

****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into the holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.

DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.

pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.

Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PRESTO DONE

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.

Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in. Plugged stove in and worked perfect.

switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering

Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.